background image

22

23

IMPORTANT:

  Britax  recommends  that  the  Versa-

Tether

®

  be  used  at  all  times.  Using  the  tether  will 

improve the stability of the child seat and reduce the 

risk of injury. Check your vehicle owner’s manual for 

approved tether anchor locations. 

If  vehicle  is  equipped  with  an  approved  tether 

anchor for the chosen seating position, remove 

Versa-Tether

® 

from pouch and place up and over 

child seat back.

Pull vehicle belt out and thread it through the forward-facing 

belt path (Fig. C). 

Verify vehicle belt is not twisted and buckle (Fig. D).

2

3

4

Push  the  child  seat  firmly  into  vehicle  seat 

while tightening vehicle belt.

If  vehicle  is  equipped  with  an  approved 

tether anchor, attach Versa-Tether

® 

hook to 

an approved tether anchor. Remove all slack 

from tether to secure. Store excess webbing 

in the tether pouch. See pages 25 – 28.

Verify that the vehicle belt is tight, locked, and child seat is secure. 

The child seat is secure when it cannot be moved front-to-back or 

side-to-side more than 1 inch (2.5 cm.) at the belt path.

Removal

If  connected,  disconnect  the  Versa-Tether

®

  from  the  tether 

anchor.

Press the red release button on the vehicle belt buckle and pull 

the vehicle buckle from the child seat belt path.

5

6

7

Lap-Belt Installation

Figure A illustrates a typical forward-facing, lap-belt 

installation. 

When not in use, always store the LATCH connectors 

in storage slots. See page 30. 

Installation: Forward-Facing

Forward-Facing

Forward-Facing

A

B

C

D

WARNING!

Child seat must be in the full upright position when installed 

in forward-facing mode with children over 33 pounds (15 kg.).

Installation: Forward-Facing

WARNING!

This child seat must not be used 

forward-facing for children less than one year 

of age 

OR

 weighing less than 20 pounds

.

IMPORTANT: 

The  child  seat  is  shipped  with  the 

buckle in position 1 (Fig. B). Use buckle position 1, 2, 

or 3 that is closest to but not underneath your child. 

See page 33 for instructions on moving the buckle.

Place child seat forward-facing on vehicle seat.

1

P276000_R2.indd   22-23

1/2/2008   10:16:11 AM

Summary of Contents for DECATHLON
























Reviews: