background image

2.2

avec la ceinture à 
3 points du 
véhicule et le pied 
de maintien 
(semi-universel)

La fixation avec la ceinture à 3 points 
et le pied de maintien se fait via une 
homologation semi-universelle. Le 
siège ne doit être utilisé que dans les 
véhicules figurant dans la liste des 
types de véhicules en annexe. Cette 
liste des types est constamment 
complétée. Pour obtenir la version la 
plus récente, veuillez nous contacter 
directement ou consulter notre site 
Internet www.britax.eu / 
www.roemer.eu

Voici comment vous pouvez utiliser 
le siège auto :

(Veuillez respecter les directives en vigueur 
dans votre pays)

1) L'utilisation sur un siège dirigé dos à 
la route (p. ex. van, minibus) est 
autorisée si celui-ci convient également 

au transport d'adultes. Ce siège ne doit pas être 
protégé par un airbag.

2) La ceinture doit être homologuée selon ECE 
R 16 (ou une norme comparable) ce qui est par 
exemple signalé par la lettre "E", "e" insérée 

dans le sens de la marche

oui

dans le sens contraire de la 
marche

non 1)

avec ceinture à 2 points

non 

avec ceinture à 3 points 2)

oui

sur le siège passager

oui 3)

sur les sièges arrière 
latéraux

oui

sur le siège arrière central 
(avec ceinture à 3 points)

oui 4)

2.2

with the vehicle's 
3-point seat belt 
and support leg
(semi-universal)

The fastening with the 3-point seat belt 
and support leg is based on semi-
universal approval. The seat may be 
used only in those vehicles cited in the 
enclosed vehicle type list. This type list 
is constantly updated. The latest 
version can be obtained from us or 
from www.britax.eu / www.roemer.eu.

You can use your child car seat as 
follows:

(Please observe the regulations applicable to 
your particular country).

1) Use is permitted on a rearward-
facing vehicle seat (e.g. in a van or 
minibus) only if the vehicle seat is also 

approved for use by adults. The seat may not be 
in the area of effect of an airbag.

2) The safety belt must be approved to ECE R 
16 or a comparable standard (see test label on 
belt with an "E" or "e" in a circle).

in the direction of travel

yes

against the direction of 
travel

no 1)

with 2-point belt

no

with 3-point belt 2)

yes

on front passenger seat

yes 3)

on outer rear seat

yes

on centre rear seat
(with 3-point belt)

yes 4)

2.2

mit dem 
3-Punkt-Gurt des 
Fahrzeuges und 
Stützbein 
(semi universal)

Die Befestigung mit 3-Punkt-Gurt und 
Stützbein erfolgt durch eine semi 
universale Genehmigung. Der Sitz darf 
nur in den Fahrzeugen verwendet  
werden, die in der beigelegten Kfz-
Typenliste aufgeführt sind. Die 
Typenliste  wird laufend ergänzt. Die 
aktuellste Version erhalten Sie direkt 
bei uns oder auf  www.britax.eu / 
www.roemer.eu.

So können Sie Ihren Auto-
Kindersitz verwenden:

(Bitte beachten Sie die Vorschriften Ihres 
Landes.)

1) Die Verwendung ist auf einem 
rückwärtsgerichteten Fahrzeugsitz (z.B. 
Van, Minibus) zulässig, der auch für 

den Transport von Erwachsenen zugelassen ist. 
Es darf kein Airbag auf den Sitz wirken.

2) Der Gurt muss nach ECE R 16 (oder 
vergleichbarer Norm) genehmigt  sein z.B. 

in Fahrtrichtung

ja

entgegen der Fahrtrichtung

nein 1)

mit 2-Punkt-Gurt

nein 

mit 3-Punkt-Gurt  2)

ja

auf Beifahrersitz

ja 3)

auf äußeren Rücksitzen

ja

auf mittlerem Rücksitz 
(mit 3-Punkt-Gurt)

ja 4)

Summary of Contents for SAFEFIX PLUS



































Reviews: