background image

Instructions for Installation & Use - Series No. 6100/A/2013

Instructions for Installation & Use - Series No. 6100/A/2013

26

27

Car's Anchor Fitting

Top Tether 
Attachment Clip

FITTING SUMMARY

Seat belt 'Lock-off'

Child use seat belt path

Hook

Storage 
Pocket

Top Tether 
Adjustment Strap

IMPORTANT: 

Always roll up the excess top tether Adjustment Strap 

and store in pocket. Always secure the loose end of the top tether strap to 

prevent it hanging out of the car or being accessible by the child.

Always secure the loose end of the top 

tether strap to prevent it hanging out of 

the car or being accessible by the child.

H.  Whilst still compressing the restraint in the 

seat pull the top tether adjustment strap (C) 
to remove any slack but do not tighten so 
much that the restraint lifts off the car seat. 

Always roll up 
excess strap and 
store in the pocket 
attached to the 
cover.

Pull Adjustment Strap 

to remove slack

C

A

EXPLANATION NOTE:

 This method of installation ensures 

good seatbelt tension, even with the child in the seat. 
We recommend that as your child grows, you should 
periodically check the seatbelt and top tether tension to 
ensure that (a) the car seatbelt has not slackened off and 
(b) that the restraint is not "hanging" on the top tether strap.

Always ensure that the car seatbelt and top tether strap are firmly restraining the restraint on the 
vehicle seat.

ALWAYS ATTACH HOOK AND REMOVE SLACK IN THE TOP TETHER STRAP.

         IMPORTANT :

FORWARD-FACING 

BELT PATH

;

marked in yellow.

FORWARD-FACING 
BELT PATH

;

marked in yellow.

HOW TO INSTALL USING SEATBELT

HOW TO INSTALL USING SEATBELT

SEATBELT

FORWARD FACING

SEATBELT

FORWARD FACING

I.  Roll up the excess strap and store in the 

pocket attached to the cover.

        CAUTION: 

CHILDREN CAN BE INJURED OR RESTRAINTS AND TOP TETHER STRAP DAMAGED BY 
UNSECURED CARGO IN A COLLISION. SECURE OR REMOVE HAZARDOUS CARGO BEFORE 
USING THIS CHILD RESTRAINT.

Pull to tighten 
seatbelt

Summary of Contents for TRUFIX


























Reviews: