ENGLISH
OPERATION MANUAL
BRITEQ
®
5/38
BT-30FC
Use DOWN and UP buttons to change the DMX512 address.
Once the correct address shows on the display, press the ENTER
button to save it.
To go back to the main menu without any change press the MENU button
shortly.
If you want to go back to normal running mode: press the MENU button
for about 2 seconds.
Channel Mode
Press the MENU button until
is shown on the display.
Press the ENTER button so the display starts blinking.
Use DOWN and UP button to select the
(16 Channel),
(9
Channel) or 1channel mode.
To use the master / slave mode with dmx control, select the
mode or the
mode.
Once the mode is selected, press the ENTER button to confirm.
To go back to the main menu without any change press the MENU button
shortly.
If you want to go back to normal running mode: press the MENU button
for about 2 seconds.
Slave Mode
Used to make the slave unit work in opposite to the master or to
work in complete sync.
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
(normal) or
(2 light
show) mode.
Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button
shortly.
If you want to go back to normal running mode: press the MENU button
for about 2 seconds.
Show Mode
Used to choose the Show mode when used in standalone or
master/slave mode.
Press the MENU button until “
ShMd
” is showing on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select one of the available shows:
Show 1 (Sh 1):
Fixture is placed
on the floor
. Tilt movement
angle 210°.
Show 2 (Sh 2):
Fixture is fixed
under ceiling
. Tilt movement angle
90°.
Show 3 (Sh 3):
Fixture is placed
on a podium, in front of the
audience.
The spot is always projecting to the audience’s
direction; i.e. in front of the stage. Pan movement angle (left to
right to left): 160°. Tilt movement angle: 90° (60° above horizon;
30° below horizon.)
Show 4 (Sh 4):
Fixture is fixed
under ceiling
. The spot is mainly
projecting in front of the stage. Pan movement angle (left to right to
left):160°. Tilt movement angle: 90° (vertically, front 75°; back 15°)
Once the right mode shows on the display, press the ENTER button to
save it.
ENGLISH
OPERATION MANUAL
BRITEQ
®
6/38
BT-30FC
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Sound Mode
The unit works to rhythm of the beat when used in standalone or master/slave mode
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
or
mode.
Once the mode has been selected, press the ENTER button save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-
signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
(yes blackout) or
(no blackout) mode.
Once the mode has been selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Led Display
Display on: display is always on.
Display off: display is off when not used.
Press the MENU button until the display shows
.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select
(display always on) or
(display off when not used).
Once the mode has been selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Pan Inversion
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
(normal) or
(pan inversion) mode.
Once the mode has been selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Tilt Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select
(normal) or
(tilt inversion) mode.
Once the mode has been selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
