background image

ENGLISH 

 

OPERATION MANUAL 

 

 
BRITEQ

®

 

5/5 

BT-H2FOG II 

TRANSPORT INSTRUCTIONS 

  Always empty the big water tank before transport: open the water evacuation tap (3) on the bottom of the 

fogger. 

  When the water tanks is empty: put the extendable PVC-hose in the big water tank. 

  To avoid spilling fog fluid: make sure that the fog liquid canister is not more than half full during transport. 

  Close the top lid of the flight case and unlock the wheel brakes. 

  Put the flight case in the truck but 

DO NOT TIP THE FLIGHT CASE !!!

 

  Always lock the brakes during transport!!! 

 

MAINTENANCE 

 

IMPORTANT:

 Always set the output to Zero and wait for minimum 30 seconds before to switch off the unit. 

This allows the unit to execute its cleaning process so all the remaining fluid is removed from the internal 
circuits.. 

  Switch off the unit, unplug the mains cable and wait until the unit has been cooled down. 

 
During inspection the following points should be checked: 

  All  screws  used  for  installing  the  device  and  any  of  its  parts  should  be  tightly  fastened  and  may  not  be 

corroded. 

  Housings,  fixations  and  installations  spots  (ceiling,  truss,  suspensions)  should  be  totally  free  from  any 

deformation. 

  The mains cables must be in impeccable condition and should be replaced immediately when even a small 

problem is detected. 

Attention: We strongly recommend internal cleaning to be carried out by qualified personnel! 
 

SPECIFICATIONS 

This unit is radio-interference suppressed. This product meets the requirements of the current European and 
national guidelines. Conformity has been established and the relevant statements and documents have been 
deposited by the manufacturer. 

Mains Input: 

AC 220-240V, 50/60Hz  

Power consumption:

 

1750 Watt 

DMX Channels:

 

Fuse: 

10A 

Warm up time: 

3.5 min 

Fog liquid tank: 

2.5L 

Recommended fog liquid:

 

BT-LOWFOG LIQUID 5L 

Optimally usable floor area:

 

+/-120m² 

Water tank:

 

+/- 10 liters 

Fog liquid consumption:

 

1-36 ml/min 

Water consumption:

 

115 ml/min 

Dimensions (L x W x H):

 

760 x 440 x 600 mm (including wheels 

– see drawing) 

Weight:

 

39 kg 

 

All the information is subject to change without prior notice 

You can download the latest version of this user manual on our website: 

www.briteq-lighting.com

   

 

Summary of Contents for BT-H2FOG II









Reviews: