9
EN
In the case of an emergency stop or an accident unsecured persons or objects may cause
injury to other vehicle occupants.
Please always check that:
• The backrests of the vehicle seats are locked (i.e. that a foldable rear seat bench latch is
engaged).
• All heavy or sharp-edged objects in the vehicle are secured.
• All persons in the vehicle have their seat belts fastened.
• The child safety seat is always secured when it is in the vehicle, even if no child is being
transported.
Some vehicle seat covers made from sensitive materials (e.g. velour, leather, etc.) may develop
wear marks when child seats are used. This can be avoided by placing a blanket or towel
under the child seat.
8. INSTALLATION OF THE CARSEAT 9-18 KG (APPROX 9MONTH-4YEARS) GROUP 1
8.1 Adjust the baby car seat into the sleeping position 3 or 4 (Fig. 11).
8.2 Remove the installation shaft (D) by pulling the moveable part of the lock from car seat
(Fig. 12A).
8.3 Pull and hold the shell forward and thread the seat belt between the shell and the base,
fasten the seat belt with the seat buckle and ensure the belt is not twisted (Fig. 13).
8.4 Put the belt through the Lock-off device (E) and Lap Belt Hooks (G), close the Lock-off
device (E). Tighten up the belt (Fig. 13A & 13B).
8.5 The seat will be fixed by two belt in two directions: one belt from the Lock-off device (E) of
the seat and the other from the Hooks (G) for lap belt.
8.6 Return the shell to its original position and thread the installation shaft (D) into the hole and
lock the device by pushing the moveable part on the other side until you hear click sound
(Fig. 12B).
8.7 Adjust the shell to most comfortable position for your child.
9. INSTALLING THE CHILD CAR SEAT (WITHOUT CHILD CAR SEAT HARNESS) 15-25KG
(APPROX 3-6 YEARS OLD) GROUP 2
Before the installation, please take away the belt system of baby car seat (including belt pads
(M), shoulder belt (N), buckle (O) and crotch strap pad (P).
Put your kid into the baby car seat, car belt pass the belt hook (B) on the top of the seat and
over the belt guide (I). And insert the belt to the buckle. (Fig. 14)
10. REMOVING THE COVERS FOR CLEANING
10.1 Loosen the shoulder belts (N) by pressing the release button (Q) and pulling the shoulder
belts (N) as far as you can. Note! Do not pull the belt pads (M) (Fig. 6).
10.2 Loosen the cover (A) all around (Fig. 15).
10.3 Pull the shoulder belts (N), buckle tongues and buckle (O) through the cover (A).
10.4 Remove the cover (A).
10.5 After washing, place the cover (A) on the shell (C).
10.6 Thread the buckle, tongues (O) and shoulder belts (N) through the cover (A) and fasten
the cover (A) at the adjusting device (Q).
10.7 Secure the cover (A) on the pins.
10.8 Close the buckle (O) and thread the shoulder belts (N) though the belt pads (M), cover (A)
and shell (C).
10.9 Connect the shoulder belts (N) to the belt anchor (H).
IMPORTANT:
The cover is a safety feature. NEVER use the car seat without it.
Summary of Contents for SafeWay
