Broadcast Tools ADCS-III Installation And Operation Manual Download | Manualshive

Page: 8 / 10

background image

e-mail:

support@broadcasttools.com

voice:

360.854.9559

fax:

866.783.1742

8

ADCS-III Installation and Operation Manual

OPERATION

Operation

Power

Insert the power plug into the power jack on the ADCS-III
and the wall transformer into the proper AC outlet. Verify
that the power LED is lit.

Act

The

ACT

ivity LED is set to trip at levels above –5dBu.

Clip

This led is set to illuminate when the input level is at +20dBu.
The clip led should occasionally flash with normal program
activity.

LT Lvl / RT Lvl

Adjust these controls to the desired AES output level.

WEBSITE:

Visit our web site for
product updates and
additional information.

«
...
6
7
8
9
10
»

Summary of Contents for ADCS-III











Reviews:

No comments

Related manuals for ADCS-III

Brand: Samson Pages: 44

Brand: HANYOUNG NUX Pages: 2

LaCinema Mini HD Connect

Brand: LaCie Pages: 4

Brand: Parker Pages: 99

Brand: Yamaha Pages: 31

GD200-037G/045P-4

Brand: INVT Pages: 266

Brand: ADDER Pages: 2

Brand: Agilent Technologies Pages: 122

Brand: Promate Pages: 28

NMP-600 - Network Media Player Connects

Brand: ViewSonic Pages: 2

Brand: DAB Pages: 1024

Brand: Barco Pages: 4

Digi Edgeport/1i

Brand: Inside Out Networks Pages: 22

Diehard 200.71522

Brand: DieHard Pages: 8

Brand: Dometic Pages: 40

SF1.6/2.2/3KTL-S

Brand: Moso Pages: 38

225 Watt Power Inverter

Brand: Vector Pages: 6

Brand: ClickTronic Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands