Standalone installation
Complete the following steps to install the device as a standalone unit on a table.
1. Unpack the device and verify the items listed under
on page 20 are present and undamaged.
2. Apply the adhesive rubber feet to the underside of the device. The rubber feet help prevent the device from sliding off the
supporting surface.
a)
Clean the indentations at each corner of the bottom of the device to ensure that they are free of dust or other debris that
might lessen the adhesion of the feet.
b) With the adhesive side against the chassis, place one rubber foot in each indentation and press into place.
3. Place the device on a sturdy flat surface.
4. Provide power to the device as described in
on page 49.
NOTE
Do not connect the device to the network until the IP address is set correctly. For instructions on how to set the IP
address, refer to
on page 51.
Installing the Universal Four-Post Rack Kit (XBR-
R000296)
Use the following instructions to install 1U and 2U devices in EIA racks that are between L-12.7 to 81.28 cm deep (L-5.0 to 32.0 in.),
where L is the chassis depth, using the Universal Four-Post Rack Kit (XBR-R000296).
There are two ways you can mount the device in a four-post rack:
•
With the port side flush with the front posts.
•
With the nonport side flush with the rear posts in a recessed position. A recessed position allows a more gradual bend in the
fiber-optic cables connected to the switch and less interference in the aisle at the front of the rack.
TABLE 10
Space requirements
Chassis with port-side
side vents
Notes
Chassis depth
Minimum rack depth
Maximum rack depth
No
Applicable to port-side and nonport-side flush
mounts.
L
L-12.7 cm (L-5 in.)
81.28 cm (32 in.)
Yes
Applicable to port-side flush mounts.
L
L-12.7 cm (L-5 in.)
81.28 cm (32 in.)
Yes
Applicable to nonport-side flush mounts.
L
L
81.28 cm (32 in.)
Note that if chassis depth (L) is less than 40.64 cm (16 in.), the chassis will not fit into a rack with a maximum depth of 81.28 cm (32 in.)
using the universal four-post rack kit. The maximum rack depth for a chassis less than 40.64 cm (16 in.) is 81.28 cm (32 in.) minus the
difference between the chassis depth and 40.64 cm (16 in.). For example, a chassis with a depth (L) of 35.56 cm (14 in.) is 5.08 cm (2
in.) smaller than 40.64 cm (16 in.), so it will install into a rack with a maximum depth of 81.28 cm (32 in.) - 5.08 cm (2 in.) = 76.2 cm
(30 in.).
Observe the following when mounting this device:
•
Two people are required to install the device in a rack. One person holds the device, while the other screws in the front and rear
brackets.
Standalone installation
Brocade G630 Hardware Installation Guide
24
53-1005235-02
Summary of Contents for Brocade G630
