background image

Broadcom

P411W-32P-UG104

4

P411W-32P PCIe 4.0 

User Guide 

NVMe Switch Adapter

P411W-32P NVMe Switch Adapter User Guide

The Broadcom

®

 P411W-32P NVMe PCIe 4.0 switch adapter (model number 50054) provides high-performance storage 

connectivity for servers and workstations. The adapter uses the PEX88048 PCIe 4.0 switch that provides a x16 PCIe 4.0, 
16 GT/s interface to a host system with up to 32 PCIe 4.0 16 GT/s ports for NVMe device connection.

NVMe technology is a logical device interface specification used to access nonvolatile storage media that attach by using a 
PCIe bus. Nonvolatile memory is usually flash memory in SSDs.

1  Features

This section lists the adapter features.

Supports 32 PCIe 4.0 lanes, which can be configured as x4, x2, and x1 ports for NVMe connectivity

Supports 16-lane, PCIe 4.0 host-interface performance

Supports PCIe link rates of 16 GT/s

Provides four internal x8 Slimline connectors (SFF-8654)

Complies with SFF-9402 sideband signaling

Offered with a full-profile bracket and a low-profile vented bracket

Provides one heartbeat LED and one system error status LED

Complies with 

SFF-TA-1005 Specification for Universal Backplane Management (UBM)

2  PCIe Interface

PCIe is a high-speed standard local bus for point-to-point interfacing of I/O components to the processor and the memory 
subsystems in high-end computers and servers. The PEX88048 switch provides the PCIe functionality for the adapter. The 
PEX88048 switch connects directly to the PCIe bus and generates timing and protocol in compliance with PCIe 
specifications.

The adapter supports 16-lane PCIe 4.0 16 Gb/s performance up to 256 Gb/s single direction and 512 Gb/s dual direction. 
Each port supports PCIe speeds up to 16 Gb/s in each direction.

3  Operating System and Driver Support

The adapter does not require a driver for operation or communication to attached NVMe drives. The drives are presented 
natively to the host and use the native NVMe drivers.

Use the inbox Fusion-MPT™ SAS driver for firmware updates. The following operating systems support the inbox 
Fusion-MPT SAS driver. See 

Firmware Download Operation

 for firmware update steps.

Microsoft Windows

VMware vSphere/ESXi

Red Hat Enterprise Linux

SuSE Linux

Ubuntu Linux

Citrix XenServer

CentOS Linux

Debian Linux

Oracle Enterprise Linux

Summary of Contents for P411W-32P





















Reviews: