2. Compare the networks that have the same network address, to determine which network is more specific. The more specific
network is the one that has more contiguous one bits in its network mask. For example, network 10.0.0.0 255.255.0.0 is more
specific than network 10.0.0.0 255.0.0.0, because the first network has 16 ones bits (255.255.0.0) whereas the second
network has only 8 ones bits (255.0.0.0).
•
–
For the less specific network, use the networks address as the ID.
–
For the more specific network, use the network’s broadcast address as the ID. The broadcast address is the network
address, with all ones bits in the host portion of the address. For example, the broadcast address for network 10.0.0.0
255.255.0.0 is 10.0.255.255.
If this comparison results in a change to the ID of an LSA that has already been generated, the router generates a new LSA to
replace the previous one. For example, if the router has already generated an LSA for network with ID 10.0.0.0 for network
10.0.0.0 255.255.255.0, the router must generate a new LSA for the network, if the router needs to generate an LSA for
network 10.0.0.0 255.255.0.0 or 10.0.0.0 255.0.0.0.
OSPF graceful restart
The OSPF Graceful Restart feature provides support for high-availability routing. With this feature enabled, disruptions in forwarding are
minimized and route flapping diminished to provide continuous service during times when a router experiences a restart.
With OSPF graceful restart enabled, a restarting router sends special LSAs to its neighbors called grace LSAs. These LSAs are sent to
neighbors either before a planned OSPF restart or immediately after an unplanned restart. The grace LSA specifies a grace period for
the neighbors of the restarting router to continue using the existing routes to and through the router after a restart. The restarting router
comes up, it continues to use its existing OSPF routes as if nothing has occurred. In the background, the router re-acquires its neighbors
prior to the restart and recalculates its OSPF routes and replaces them with new routes as necessary. Once the grace period has passed,
the adjacent routers return to normal operation.
NOTE
By default, graceful restart is enabled.
NOTE
If a Brocade ICX 6650 device is configured for OSPF graceful restart and is intended to be used in switch over, the OSPF
dead-interval should be changed to 60 seconds on OSPF interfaces to ensure that the graceful restart process succeeds
without a timeout.
OSPF stub router advertisement
OSPFv2 stub router advertisement is an open standard based feature and it is specified in RFC 3137. This feature provides a user with
the ability to gracefully introduce and remove an OSPFv2 router from the network by controlling when the data traffic can start and stop
flowing through the router in case where there are other OSPFv2 routers present on the network providing alternative paths for the traffic.
This feature does not work if there is no alternative for the traffic through other OSPFv2 routers. The router can control the data traffic
flowing through it by changing the cost of the paths passing through the configured router. By setting the path cost high the traffic will be
redirected to other OSPFv2 routers providing a lower cost path. This change in path cost is accomplished by setting the metric of the
links advertised in the Router LSA to a maximum value. When the OSPFv2 router is ready to forward the traffic the links are advertised
with the real metric value instead of the maximum value.
The feature is useful for avoiding a loss of traffic during short periods when adjacency failures are detected and traffic is rerouted. Using
this feature, traffic can be rerouted before an adjacency failure occurs due to common services interruptions such as a router being
shutdown for maintenance.
OSPF graceful restart
FastIron Ethernet Switch Layer 3 Routing
230
53-1003627-04
Summary of Contents for FastIron SX 1600
