To disable the logging of events, enter the following command.
device(config-ospf6-router)# no log-status-change
Syntax:
[no] log-status-change
To re-enable the logging of events, enter the following command.
device(config-ospf6-router)# log-status-change
IPsec for OSPFv3
IPSec secures OSPFv3 communications by authenticating and encrypting each IP packet of a communication session.
IPsec is available for OSPFv3 traffic only and only for packets that are “for-us”. A for-us packet is addressed to one of the IPv6
addresses on the device or to an IPv6 multicast address. Packets that are just forwarded by the line card do not receive IPsec scrutiny.
Brocade devices support the following components of IPsec for IPv6-addressed packets:
•
Authentication through Encapsulating Security Payload (ESP) in transport mode
•
HMAC-SHA1-96 as the authentication algorithm
•
Manual configuration of keys
•
Configurable rollover timer
IPsec can be enabled on the following logical entities:
•
Interface
•
Area
•
Virtual link
With respect to traffic classes, this implementation of IPSec uses a single security association (SA) between the source and destination to
support all traffic classes and so does not differentiate between the different classes of traffic that the DSCP bits define.
IPsec on a virtual link is a global configuration. Interface and area IPsec configurations are more granular.
Among the entities that can have IPsec protection, the interfaces and areas can overlap. The interface IPsec configuration takes
precedence over the area IPsec configuration when an area and an interface within that area use IPsec. Therefore, if you configure IPsec
for an interface and an area configuration also exists that includes this interface, the interface’s IPsec configuration is used by that
interface. However, if you disable IPsec on an interface, IPsec is disabled on the interface even if the interface has its own, specific
authentication.
For IPsec, the system generates two types of databases. The
security association database
(SAD) contains a security association for
each interface or one global database for a virtual link. Even if IPsec is configured for an area, each interface that uses the area’s IPsec still
has its own security association in the SAD. Each SA in the SAD is a generated entry that is based on your specifications of an
authentication protocol (ESP in the current release), destination address, and a security policy index (SPI). The SPI number is user-
specified according to the network plan. Consideration for the SPI values to specify must apply to the whole network.
The system-generated security policy databases (SPDs) contain the security policies against which the system checks the for-us packets.
For each for-us packet that has an ESP header, the applicable security policy in the security policy database (SPD) is checked to see if
this packet complies with the policy. The IPsec task drops the non-compliant packets. Compliant packets continue on to the OSPFv3
task.
Configuring OSPFv3
FastIron Ethernet Switch Layer 3 Routing
312
53-1003627-04
Summary of Contents for FastIron SX 1600
