Hello 739 738 29556 29520
DbDesc 2 2 236 2536
LSReq 1 1 1444 88
LSUpdate 344 258 71464 23256
LSAck 30 291 6780 11396
OSPF messages dropped,no authentication: 0
ve 17 admin up, oper up, IPv6 enabled
IPv6 Address:
fe80::214:ff:fe77:96ff
5100::192:213:111:213/112
5100::192:213:111:0/112
Instance ID 0, Router ID 192.168.98.213
Area ID 0.0.0.200, Cost 1, Type BROADCAST
MTU: 10178
State BDR, Transmit Delay 1 sec, Priority 1, Link-LSA Tx not suppressed
Timer intervals :
Hello 10, Hello Jitter 10 Dead 40, Retransmit 5
Authentication Use: Enabled
KeyRolloverTime(sec): Configured: 300 Current: 0
KeyRolloverState: NotActive
Outbound: None
Inbound: None
DR:192.168.98.111 BDR:192.168.98.213 Number of I/F scoped LSAs is 2
DRElection: 1 times, DelayedLSAck: 7 times
Neighbor Count = 1, Adjacent Neighbor Count= 1
Neighbor:
192.168.98.111 (DR)
Statistics of interface ve 17 :
Type tx rx tx-byte rx-byte
You can display detailed OSPFv3 information about a specific interface using the following command at any level of the CLI.
Syntax:
show ipv6 ospf interface
[
brief
] [
ethernet
unit/slot/port
] [
loopback
number
] [
tunnel
number
] [
ve
number
]
The
ethernet
,
loopback
,
tunnel
, and
ve
parameter specify the interface for which to display information. If you specify an Ethernet
interface, also specify the port number associated with the interface. If you specify a loopback, tunnel, or VE interface, also specify the
number associated with the interface.
TABLE 75
show ipv6 ospf interface output descriptions
This field
Displays
Interface status
The status of the interface. Possible status includes the following:
•
Up.
•
Down.
Type
The type of OSPFv3 circuit running on the interface. Possible types
include the following:
•
BROADCAST
•
POINT TO POINT UNKNOWN
•
POINT TO POINT
IPv6 Address
The IPv6 address assigned to the interface.
Instance ID
An identifier for an instance of OSPFv3.
Router ID
The IPv4 address of the device. By default, the router ID is the IPv4
address configured on the lowest numbered loopback interface. If the
device does not have a loopback interface, the default router ID is the
lowest numbered IPv4 address configured on the device.
Area ID
The IPv4 address or numerical value of the area in which the interface
belongs.
Cost
The overhead required to send a packet through the interface.
default
Shows whether or not the default passive state is set.
Displaying OSPFv3 information
FastIron Ethernet Switch Layer 3 Routing
328
53-1003627-04
Summary of Contents for FastIron SX 1600
