background image

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, 
and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: 

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate 

the equipment.

 

NOTE: 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, there 
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following 
measures:
 
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help

Information Regarding Exposure to Radio Frequency Energy 

Your device is designed and manufactured not to exceed the emission limits for exposure to RF energy set by the Federal Communications Commission 
of the United States (FCC). Information on your Device is on file with the FCC and can be found under the Display Grant section of 
http://www.fcc.gov/oet/ea/ after searching on the FCC ID for your Device, which can be found on the back of the Device.

LITHIUM POLYMER BATTERY WARNINGS

This device contains a non-removable Lithium-Polymer battery. The battery must be recycled or disposed of properly. 
Contact your local waste management office for information on battery recycling or disposal.

Rating Label Definitions

Direct current symbol.

This symbol signifies the product must not be discarded as household waste, and should be delivered to an appropriate collection facility 
for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. 

This symbol signifies and declares that this equipment has battery charging which complies with California CEC and energy efficiency.

This symbol signifies that this is a wireless device powered by Bluetooth® technology. The Bluetooth® word mark and logos are registered 
trademarks owned by Bluetooth SIG, Inc., used under license.

FCC INFORMATION

20

Summary of Contents for BIG BLUE PARTY

























Reviews: