Carry the SmartStep
™
Pedometer anywhere!
Put it in your pocket or purse, or hang
it from the included lanyard. It will
track steps and miles traveled, plus
calories and fat grams burned. It even
resets itself at midnight, plus tracks
your progress for seven days.
BATTERY PRECAUTIONS
Dispose of the old battery
properly. Do not dispose of
the old battery in a fire.
Do not leave the battery where
a child or pet could play with
or swallow it. If the battery is
swallowed, contact a
physician immediately.
The battery may explode
if mistreated. Do not attempt
to recharge or disassemble
the battery.
Use only a fresh battery of
the required size and type.
SAVE THESE INSTRUCTIONS
•
•
•
•
6
2
3
4
9
6
_I
N
S
0
5
1
0
_S
m
ar
tS
te
p
P
ed
om
et
er
In
st
ru
ct
io
ns
D
oc
. S
iz
e:
3
0
0
m
m
W
x
1
1
5
m
m
H
Fo
ld
ed
S
iz
e:
5
0
m
m
W
x
1
1
5
m
m
H
O
ut
pu
t
at
1
0
0
%
P
rin
ts
1
/1
B
la
ck
Fi
ni
sh
in
g:
T
rim
t
o
C
ro
ps
; A
cc
or
di
an
F
ol
d:
5
f
ol
ds
623496
Merrimack, New Hampshire, USA 03054
800-846-3000 • www.Brookstone.com
SmartStep
™
Pedometer
ACCurAte—Anywhere
you CArry it
LOCATION Of CONTROLS
OPERATION
Your SmartStep
™
Pedometer comes
with a battery already installed.
Remove the plastic strip from the
BATTERY COMPARTMENT by
pulling the tab and sliding it out from
between the battery contacts.
fIRST TImE SET-UP
1. Press and hold the SET button until
the LCD SCREEN shows all zeros
and the hour number blinks.
2. Set the hour by using the
MEMORY/ and MODE/
buttons to scroll through the
numbers. Holding down either the
MEMORY/ or MODE/ button
will scroll through the numbers
rapidly. Press the SET key to
select the hour.
3. The minute number will blink
on the LCD screen.
4. Set the minutes by using the
MEMORY/ and MODE/
buttons to scroll through the
numbers. Holding down the
MEMORY/ or MODE/
button will scroll through the
numbers rapidly. Press the SET
key to select your minutes.
note: the SmartStep
™
Pedometer
uses 24 hour (military time) to
allow for daily reset.
5. The weight number will blink
on the LCD screen.
6. Set your weight by using the
MEMORY/ and MODE/
buttons to scroll through the
numbers. Holding down the
MEMORY/ or MODE/
button will scroll through the
numbers rapidly. Press the SET
key to select your weight.
7. The stride number will blink
on the LCD screen.
Setting SteP/Stride Length
You must set your step/stride length
in the pedometer for it to accurately
calculate distance traveled.
1. Take five steps or strides and
measure the distance covered
in inches using a tape measure.
Divide that number by five. This is
your average step/stride length.
2. Set your stride length in inches
by using the MEMORY/ and
MODE/ buttons to scroll
through the numbers. Holding
down the MEMORY/ or
MODE/ buttons will scroll
through the numbers rapidly.
3. Press the SET key to select
your stride.
1. LCd Screen
2. read-out
titles
3. Memory /
Button
4. Mode /
Button
5. Set Button
6. Battery
Compartment
Cover
7. Battery
Compartment
8. open Position
9. Close Position
10. reset Button
11. Lanyard hole
12. Lanyard
(not shown)
1
9
11
3
6
8
7
10
2
4
5