Brother 09055CDN Service Manual Download

Page: 147 / 590

2-108

Confidential

■

Paper jam at the MP tray (Error code 8C)

<User Check>

- Check if the paper is loaded into the MP tray correctly.

- Turn back the paper loaded in the MP tray or change the orientation of the paper by 180°.

- Adjust the paper guide corresponding to the paper size.

- Check if too much paper is loaded in the tray.

- Check if the thickness of the paper is 60 to 163 g/m

■

Paper jam around the belt unit (Error code 88, etc.)

<User Check>

- Check if the belt unit is properly installed.

Step

Cause

Remedy

Foreign object around MP tray

Remove the foreign object.

MP paper feeding kit worn out

Replace the MP paper feeding kit.

MP registration front sensor
failure

Check the sensor performance following
the procedure described in

“Function code

32”

. If any problem occurs, replace the

MP paper empty/registration front sensor
PCB ASSY.

Engine PCB failure

Replace the engine PCB ASSY.

Main PCB failure

Replace the main PCB ASSY.

Step

Cause

Remedy

Registration rear actuator
malfunction

Re-assemble the registration rear
actuator.

Paper eject actuator
malfunction

Re-assemble the paper eject actuator.

Harness connection failure of
paper eject sensor PCB ASSY

Check the harness connection of the
paper eject sensor PCB ASSY and
reconnect it.

Harness connection failure of
drum drive motor

Check the harness connection of the
drum drive motor and reconnect it.

Paper eject sensor PCB failure

Replace the paper eject sensor PCB
ASSY.

Drum drive motor failure

Replace the drum drive motor.

Rotation failure of the heat roller

Replace the fuser unit.

Engine PCB failure

Replace the engine PCB ASSY.

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for 09055CDN















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 09055CDN

Reviews:

Related manuals for 09055CDN

Brands by name

Popular brands

Brother 09055CDN, Service Manual

Search results

Summary of Contents for 09055CDN

Reviews:

Related manuals for 09055CDN

Brands by name

Popular brands