Brother 09055CDN Service Manual Download | Manualshive

Page: 21 / 590

background image

x

Confidential

■

Caution for Laser Product (WARNHINWEIS fur Laser drucker)

<Location of the scanner windows>

■

Additional Information

When servicing the optical system of the machine, be careful not to place a screwdriver or
other reflective object in the path of the laser beam. Be sure to take off any personal
accessories such as watches and rings before working on the machine. A reflected beam,
though invisible, can permanently damage the eyes.

Since the beam is invisible, the following caution label is attached on the laser unit.

CAUTION:

When the machine during servicing is operated with the cover open, the
regulations of VBG 93 and the performance instructions for VBG 93 are
valid.

CAUTION:

In case of any trouble with the laser unit, replace the laser unit itself. To
prevent direct exposure to the laser beam, do not try to open the
enclosure of the laser unit.

ACHTUNG:

Im Falle von Störungen der Lasereinheit muß diese ersetzt werden. Das
Gehäuse der Lasereinheit darf nicht geöffnet werden, da sonst Laser-
strahlen austreten können.

«
...
19
20
21
22
23
...
»

Summary of Contents for 09055CDN















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 09055CDN

Brand: Pantum Pages: 164

Pixma TS7700i Series

Brand: Canon Pages: 554

Brand: Telpar Pages: 52

Brand: Oki Pages: 20

Brand: idp Pages: 63

Brand: Ascend Pages: 6

Brand: Tektronix Pages: 178

Brand: SPRT Pages: 12

Nuvera 100 roduction Systems

Brand: Xerox Pages: 70

LaserMatrix LM2405

Brand: Output Technology Pages: 249

Brand: Olivetti Pages: 315

Brand: Xerox Pages: 78

Brand: Epson Pages: 16

Brand: Epson Pages: 2

Brand: Epson Pages: 36

Brand: Epson Pages: 47

Brand: Epson Pages: 16

C11CA56203 - PictureMate Charm PM 225 Color Inkjet Printer

Brand: Epson Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands