Brother 09055CDN Service Manual Download

Page: 452 / 590

5-14

Confidential

WSW31

Function setting 9

WSW32

Function setting 10

WSW33

Function setting 11

WSW34

Function setting 12

WSW35

Function setting 13

WSW36

Function setting 14

WSW37

Function setting 15

WSW38

V.34 transmission settings

WSW39

V.34 transmission speed

WSW40

V.34 modem settings

WSW41

ON-duration of the scanning light source

WSW42

Internet mail settings

WSW43

Function setting 16

WSW44

Speeding up scanning-1

WSW45

Speeding up scanning-2

WSW46

Monitor of power ON/OFF state and parallel port kept at high

WSW47

Switching between high-speed USB and full-speed USB

WSW48

USB setup latency

WSW49

End-of-copying beep

WSW50

SDAA settings

WSW51

Function setting 17

WSW52

Function setting 18

WSW53

Function setting 19

WSW54

Function setting 20

WSW55

Interval of time required for the developing bias voltage correction

WSW56

Function setting 21

WSW57

Function setting 22

WSW58

Function setting 23

WSW59

Function setting 24

WSW60

Function setting 25

WSW61

Scanning light intensity to judge to be stable 1

WSW62

Scanning light intensity to judge to be stable 2

WSW63

Function setting 26

WSW64

Setting the language/Default paper size

WSW65

Setting the paper support

WSW66

Reserved (Change of the setting is prohibited)

WSW67

Reserved (Change of the setting is prohibited)

WSW No.

Function

Summary of Contents for 09055CDN















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 09055CDN

Reviews:

Related manuals for 09055CDN

Brands by name

Popular brands

Brother 09055CDN, Service Manual

Search results

Summary of Contents for 09055CDN

Reviews:

Related manuals for 09055CDN

Brands by name

Popular brands