Brother 09055CDN Service Manual Download

Page: 455 / 590

5-17

Confidential

1.4.7 Operational check of LCD (Function code 12)

<Function>

This function allows you to check whether the LCD on the control panel works normally.

<Operating procedure>

(1) Press the

and

buttons in this order in the initial state of the maintenance mode.

The LCD shows.

(2) Each time you press the

Start/Black

button, the LCD cycles through the displays as

shown below.

(3) When the

Stop/Exit

button is pressed regardless of the display, the machine cancels the

operation, beeps for one second and returns to the initial state of the maintenance mode.

Non Touch panel model

Backlight
LCD
Data LED
Error LED

: ON
: Display of all dots ON
: ON
: ON

Backlight
LCD
Data LED
Error LED

: ON
: Display of all dots OFF
: ON
: ON

Backlight
LCD
Data LED
Error LED

: OFF
: Display of all dots ON
: ON
: ON

Backlight
LCD
Data LED
Error LED

: OFF
: Display of all dots OFF
: ON
: ON

Fig. 5-7

Display 2

Display 1

Display 4

Display 3

Summary of Contents for 09055CDN















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 09055CDN

Reviews:

Related manuals for 09055CDN

Brands by name

Popular brands

Brother 09055CDN, Service Manual

Search results

Summary of Contents for 09055CDN

Reviews:

Related manuals for 09055CDN

Brands by name

Popular brands