background image

54

When saving is finished, the following message 
appears. For details on checking data saved in 
CanvasWorkspace, refer to the Help for 
CanvasWorkspace.

d

Touch the “OK” key to finish saving the data.

Retrieve Data

a

Touch the “Retrieve Data” key in the home 
screen to display the recall source selection 
screen.

b

To use the data from a USB flash drive, insert 
the USB flash drive into the USB port (for a 
USB flash drive) on this machine.

c

Touch where you saved the pattern to be 
retrieved, and then select the pattern.

a

Retrieve from machine's memory key

b

Retrieve from USB flash drive key

c

Retrieve from CanvasWorkspace key (via a 
wireless network connection) 

d

Retrieve from CanvasWorkspace key (using 
a USB cable)

a

Retrieve from the machine’s memory.

Touch the pattern to be retrieved and display.

b

Retrieve from a USB flash drive.

If there are folders on the USB flash drive, touch 
a folder to display the list of patterns that it 
contains.

If there are many folders or patterns, touch the 
arrows keys in the screen to scroll up or down.

Memo

It may take some time for the USB flash drive to 
be detected. Wait 5 to 6 seconds after inserting 
the USB flash drive before pressing a key. (The 
length of time differs depending on the USB 
flash drive.)

When using a USB flash drive with an access 
indicator, wait until the indicator stops flashing.

If an error is indicated, touch 

 again.

Touch the pattern to be retrieved and display.

Memo

When retrieving pattern data from the 
machine’s memory or a USB flash drive, the 
size of the thumbnail previews can be changed. 

Touch 

 to display the settings screen, and 

then touch 

 or 

 to change the size.

a

c

b

d

Summary of Contents for 891-Z05















































































































Reviews: