background image

106

Adjusting the Screen

If the screen does not respond correctly when you 
touch a key (the machine does not perform the 
operation or performs a different operation), follow 
the steps below to make the proper adjustments.

a

Holding your finger on the LCD screen, turn 
the main power to off and back to on. Keep 
your finger on the LCD screen, until Brother 
logo disappears.

The touch panel adjustment screen is displayed.

b

Using the included touch pen (stylus), lightly 
touch the center of each +, in order from 1 to 
5. If an error occur when to, start 
again from number 1.

After completing the touch panel adjustment, the 
message “SUCCESS” appears on the screen.

c

Turn the main power to off, then turn it back to 
on.

Note

If you finish the screen adjustment and the 
screen still does not respond correctly, or if you 
cannot do the adjustment, contact the retailer 
who sold you this machine or the nearest 
authorized service center.

Adjusting the Scanning/Cutting 
Position

In “Direct Cut” mode, the cutting position can be 
automatically adjusted if it has shifted.
For details on the “Direct Cut” mode, see 
“SCANNING FOR CUTTING (Direct Cut)” on 
page 67
.

Materials

Memo

• Be sure to first test attach it to a mat suitable 

for the paper.

a

Insert the holder into the carriage.

• For details, follow the procedures under “Installing 

and Uninstalling the Holder” on page 26.

b

Attach the paper to the mat.

• Align the upper-left corner of the paper with the 

upper-left corner of the mat.

• For details on attaching the paper, follow the 

procedure under “Attaching the Material (Paper)” 
on page 18.

a

Long side

b

Short side

Paper

Thick paper
Color: White
Size: A4 size (210 mm × 297 mm) or 
Letter size (216 mm × 279 mm)
Thickness: 0.2 to 0.3 mm 
(recommended)

Mat

Mat suitable for the material (See 
page 15.)

Cutting 

blade

Auto Blade Holder (black)

a

b

Summary of Contents for 893-Z11

































































































































Reviews: