background image

26

Installing and Uninstalling the Holder

Select the holder appropriate for the material, and 
then install it into the machine. For details on the 
holder appropriate for the material, see “Reference 
Table of Mat, Blade and Material Combinations” on 
page 15
.

a

Press 

 in the operation panel to turn on the 

machine.

For details, see “Turning On/Off the Machine” on 
page 8.

Note

Be sure to turn on the machine before installing 
the holder.

If the holder is installed while the machine is off, 
the blade may break and material may not be 
cut cleanly.

b

Remove the protective cap.

Note

Please remove protective cap from blade 
holder before placing it into the machine 
carriage.

 WARNING

This is not a toy and is not intended to be used 
by children.  In order to prevent choking 
hazards, do not allow infants/children to put the 
protective caps in their mouths.

 CAUTION

Do not press the tip of the holder with your 
hand or fingers because the tip of the blade will 
extend and may result in injuries.

Do not touch the tip of the blade with your 
hands or fingers. There is a risk of injury.

c

Grasp the holder grip, and then insert the 
holder into the carriage.

a

Grip

d

Push down on the holder lock lever.

Firmly push down until the holder is locked in place.

a

Holder lock lever

e

Reverse the installation procedure to uninstall 
the holder.

 WARNING

• This is not a toy and is not intended to be used 

by children.  In order to prevent choking 
hazards, do not allow infants/children to put the 
protective caps in their mouths.

 CAUTION

• After removing the blade holder from the 

machine, be sure to attach the protective cap.

• Do not press the tip of the holder with your 

hand or fingers because the tip of the blade will 
extend and may result in injuries.

• Do not touch the tip of the blade with your 

hands or fingers. There is a risk of injury.

a

a

a

Summary of Contents for 893-Z11

































































































































Reviews: