manualshive.com logo in svg

Brother DCP-8040, Service Manual

The Brother DCP-8040 is a versatile multifunction printer that offers high-quality printing, scanning, and copying capabilities. With its advanced features and user-friendly interface, this efficient device is perfect for both home and office use. Download the free brochure & specs manual from 88.208.23.73:8080 to explore all the functionalities of this exceptional printer.

Share
Download
background image

CHAPTER 4 DISASSEMBLY AND RE-ASSEMBLY 

 

4-52

(15) Remove the cup S M3x6 Tite screws, and then remove the MP gear cover. 

(16) Remove the MP roller cover. 

(17) Remove the MP-PE sensor PCB ASSY. 

 

Fig. 4-91 

 

3.18  Rear Cover Sensor 

(1)  Disconnect the connector, and then remove the rear cover sensor. 

 

Fig. 4-92 

MP-PE sensor PCB ASSY 

Hook (pin) 

Hook 

Hooks 

Rear cover sensor 

Connector 

Hook 

MP chute ASSY 

Tite, cup S M3x6 

MP gear cover 

Hook (pin) 

MP roller cover 

Hook 

Summary of Contents for DCP-8040
















































































































































































































































































































































































Reviews:

No comments

Related manuals for DCP-8040

Canon iPF650 - imagePROGRAF Color Inkjet Printer Basic Manual preview
iPF650 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 40
Canon iP90 - PIXMA Color Inkjet Printer Easy Setup Instructions preview
iP90 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 2
Canon iPF650 - imagePROGRAF Color Inkjet Printer Install Manual preview
iPF650 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 16
Canon iP100 - PIXMA Color Inkjet Printer Setup Instructions preview
iP100 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 2
Canon imageRUNNER ADVANCE C5560 Configuration And Installation Manual preview
imageRUNNER ADVANCE C5560
Brand: Canon Pages: 67
Canon imageRUNNER 3300 Reference Manual preview
imageRUNNER 3300
Brand: Canon Pages: 366
Canon IMAGERUNNER ADVANCE C5051 Getting Started preview
IMAGERUNNER ADVANCE C5051
Brand: Canon Pages: 252
Canon iPF710 - imagePROGRAF Color Inkjet Printer Operations preview
iPF710 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 2
Canon iR1018 Portable Manual preview
iR1018
Brand: Canon Pages: 86
Canon iR1018 Installation Procedure preview
iR1018
Brand: Canon Pages: 20
TDT RX6 Ultrasonic Recording Manual preview
RX6
Brand: TDT Pages: 15
Samsung CLP-680ND: CLP-775ND Quick Installaion Manual preview
CLP-680ND: CLP-775ND
Brand: Samsung Pages: 2
QMS 4060 Supplementary Manual preview
4060
Brand: QMS Pages: 27
QMS 4060 Accessories Manual preview
4060
Brand: QMS Pages: 3
Xerox PHASER 6121MFP Service Manual preview
PHASER 6121MFP
Brand: Xerox Pages: 532
Xerox Phaser 6120 User Manual preview
Phaser 6120
Brand: Xerox Pages: 174
Xerox Phaser 6115 MFP Repacking Manual preview
Phaser 6115 MFP
Brand: Xerox Pages: 2
Xerox Phaser 6115 MFP User Manual preview
Phaser 6115 MFP
Brand: Xerox Pages: 219

Brands by name

Popular brands

Load more brands