manualshive.com logo in svg

Brother DCP-8040, Service Manual

The Brother DCP-8040 is a versatile multifunction printer that offers high-quality printing, scanning, and copying capabilities. With its advanced features and user-friendly interface, this efficient device is perfect for both home and office use. Download the free brochure & specs manual from 88.208.23.73:8080 to explore all the functionalities of this exceptional printer.

Share
Download
background image

CHAPTER 4 DISASSEMBLY AND RE-ASSEMBLY 

 

4-74

(10) Remove the bearing L from the P/R shaft. 

(11) Remove the P/R shaft. 

 

 

Fig. 4-130 

 

(12) Remove the idle gear 22. 

(13) Remove the middle roller gear. 

(14) Remove the bind B M3x10 taptite screw and the conductor bearing. 

(15) Remove the 1st F/R shaft. 

 

 

Fig. 4-131 

Bearing L 

P/R shaft 

1st F/R shaft

Conductor bearing

Taptite bind B M3x10 

Idle gear 22 

Frame 

Hook 

1 

2 

Middle roller gear 

Summary of Contents for DCP-8040
















































































































































































































































































































































































Reviews:

No comments

Related manuals for DCP-8040

VASTEX V-100 Manual preview
V-100
Brand: VASTEX Pages: 15
Xerox DocuPrint C525 A Quick Reference Manual preview
DocuPrint C525 A
Brand: Xerox Pages: 49
Xerox DocuPrint C2100 Quick Reference Manual preview
DocuPrint C2100
Brand: Xerox Pages: 206
Xerox DocuPrint 96 Installation Planning Manual preview
DocuPrint 96
Brand: Xerox Pages: 116
Xerox DocuPrint 96 Message Manual preview
DocuPrint 96
Brand: Xerox Pages: 358
Xerox DocuPrint 4635 Operator'S Manual preview
DocuPrint 4635
Brand: Xerox Pages: 344
Xerox DocuPrint 205 Operation Manual preview
DocuPrint 205
Brand: Xerox Pages: 59
Xerox DocuPrint 900 Product Safety Data Sheet preview
DocuPrint 900
Brand: Xerox Pages: 2
Xerox C230 Quick Reference Manual preview
C230
Brand: Xerox Pages: 10
Xerox DocuPrint 180 Maintenance Manual preview
DocuPrint 180
Brand: Xerox Pages: 51
Xerox DocuPrint 180 Solution Manual preview
DocuPrint 180
Brand: Xerox Pages: 110
Xerox 7300DX - Phaser Color Laser Printer Overview preview
7300DX - Phaser Color Laser Printer
Brand: Xerox Pages: 8
Xerox 8400B - Phaser Color Solid Ink Printer Reference Manual preview
8400B - Phaser Color Solid Ink Printer
Brand: Xerox Pages: 203
Xerox 3150 - Phaser B/W Laser Printer Product Data Sheet preview
3150 - Phaser B/W Laser Printer
Brand: Xerox Pages: 2
Xerox 3117 - Phaser B/W Laser Printer Upgrade Instructions preview
3117 - Phaser B/W Laser Printer
Brand: Xerox Pages: 8
Xerox C8 - DocuPrint Color Inkjet Printer System Administration Manual preview
C8 - DocuPrint Color Inkjet Printer
Brand: Xerox Pages: 148
Xerox 1235DT - Phaser Color Solid Ink Printer Service Manual preview
1235DT - Phaser Color Solid Ink Printer
Brand: Xerox Pages: 239
Xerox 1075 Operating Instructions Manual preview
1075
Brand: Xerox Pages: 64

Brands by name

Popular brands

Load more brands