manualshive.com logo in svg

Brother DCP-8040, Service Manual

The Brother DCP-8040 is a versatile multifunction printer that offers high-quality printing, scanning, and copying capabilities. With its advanced features and user-friendly interface, this efficient device is perfect for both home and office use. Download the free brochure & specs manual from 88.208.23.73:8080 to explore all the functionalities of this exceptional printer.

Share
Download
background image

CHAPTER 4 DISASSEMBLY AND RE-ASSEMBLY 

 

4-82

(18) Remove the bind B M3x10 Taptite screw. 

(19) Remove the P/R solenoid ASSY, the P/R solenoid lever and the solenoid release spring 

P/R. 

(20) Remove the bind B M3x10 Taptite screw. 

(21) Remove the F/R solenoid ASSY and solenoid release spring F/ R. 

 

 

Fig. 4-146 

 

(22) Disconnect the connector from the front cover sensor. 

(23) Remove the bind B M3x10 Taptite screw. 

(24) Remove the toner LED PCB unit ASSY. 

(25) Remove the sensor clip. 

(26) Remove the front cover sensor from the frame L. 

 

Fig. 4-147 

Taptite, bind B M3x10 

F/R solenoid 
ASSY 

Solenoid release spring P/R 

P/R solenoid ASSY 

Toner LED PCB 
unit ASSY 

Sensor clip 

Front cover sensor 

Sensor clip 

P/R solenoid lever 

Solenoid release 
spring F/R 

Taptite, bind B M3x10 

Taptite, bind B M3x10 

Frame L 

Front cover sensor 

Connector 

Summary of Contents for DCP-8040
















































































































































































































































































































































































Reviews:

No comments

Related manuals for DCP-8040

Xerox 7142 Service Manual preview
7142
Brand: Xerox Pages: 341
LabelTac Pro X User Manual preview
Pro X
Brand: LabelTac Pages: 15
Pantum P3060 SERIES Manual preview
P3060 SERIES
Brand: Pantum Pages: 115
Kyocera KM-1820 Quick Start Manual preview
KM-1820
Brand: Kyocera Pages: 2
Intellisystem ThermalTronix TT-1260S-UTCM User Manual preview
ThermalTronix TT-1260S-UTCM
Brand: Intellisystem Pages: 18
Pantum L2710 Series User Manual preview
L2710 Series
Brand: Pantum Pages: 164
Olivetti Copia 9915F Operation Manual preview
Copia 9915F
Brand: Olivetti Pages: 228
InfoPrint Color 1824 User Manual preview
Color 1824
Brand: InfoPrint Pages: 170
Wang 1111M Maintenance Manual preview
1111M
Brand: Wang Pages: 39
DataCard MX6000 Datasheet preview
MX6000
Brand: DataCard Pages: 2
Lexmark Platinum Pro900 Quick Reference Manual preview
Platinum Pro900
Brand: Lexmark Pages: 27
Lexmark XC4100 Series User Manual preview
XC4100 Series
Brand: Lexmark Pages: 158
Lexmark MS810n Mono Quality Manual preview
MS810n
Brand: Lexmark Pages: 1
Lexmark MS510 Series Setup Sheet preview
MS510 Series
Brand: Lexmark Pages: 2
Lexmark W850dn Manual preview
W850dn
Brand: Lexmark Pages: 327
Lexmark C950 Series Moving Manual preview
C950 Series
Brand: Lexmark Pages: 2
Lexmark Clinical Assistant X646dte User Manual preview
Clinical Assistant X646dte
Brand: Lexmark Pages: 16
Lexmark 850e - X VE4 B/W Laser Troubleshooting Manual preview
850e - X VE4 B/W Laser
Brand: Lexmark Pages: 6

Brands by name

Popular brands

Load more brands