manualshive.com logo in svg

Brother DCP-8040, Service Manual

The Brother DCP-8040 is a versatile multifunction printer that offers high-quality printing, scanning, and copying capabilities. With its advanced features and user-friendly interface, this efficient device is perfect for both home and office use. Download the free brochure & specs manual from 88.208.23.73:8080 to explore all the functionalities of this exceptional printer.

Share
Download
background image

MFC-8440/8840D/8840DN, DCP-8040/8045D/8045DN

SERVICE MANUAL

6-7

2.2

Error Codes Shown in the “MACHINE ERROR X X” message.

If the LCD shows the "PLS OPEN COVER" message, you can display the detailed error code
following the MACHINE ERROR, by using the maintenance-mode function code 82 described
in Chapter 7, Section 3.16.

NOTE:

•

 

When checking a PCB as instructed in the "Check:" column, check its harness also.

•

 

To check sensors, use the maintenance-mode function code 32 described in Chapter 7,

Section 3.9 (that is, press the 

3

 and 

2

 keys in the maintenance mode).

Error

Code

(Hex)

Error factor

Check:

56

MP front cover opened.

•

  MP front cover

57

Recording paper jam (inside DX unit).

•

 DX 

unit

58

Reserved
(Recording paper jam (no DX unit)).

•

 DX 

unit

59

Reserved
(Recording paper jam (inside MP tray)).

•

 MP 

tray

5A

Reserved
(Out of recording paper).

•

 Recording 

paper

5B

Reserved  (Paper size error in case of
double-sided print).

•

 Recording 

paper

5C

Reserved  (Paper size error of one side only
in case of double-sided print).

5D

Reserved
(MP tray sensor remains ON).

•

  MP tray sensor

5E

Reserved
(MP tray sensor remains OFF).

•

  MP tray sensor

5F

Reserved
(DX unit sensor is inactivated).

•

  DX unit sensor

6A

Heater warming-up timeout error.
(Heater does not reach 60

°

C within 11 sec.)

•

 Thermistor 

ASSY

•

 Halogen 

lamp

6B

Heater warming-up timeout error.
(Heater does not reach 100

°

C within 15

sec.)

•

 Thermistor 

ASSY

•

 Halogen 

lamp

6C

Heater temperature exceeds the maximum
high temperature.
(270

°

C or more is detected for 1 sec.)

•

 Thermistor 

ASSY

•

  Power supply PCB

6D

Heater temperature lowers the minimum
low temperature.
(60

°

C or less is detected for 1 sec.)

•

 Thermistor 

ASSY

•

  Power supply PCB

6E

Heater temperature does not go up enough.
(Slower temperature rise rate than 2

°

C/5

sec. is detected.)

•

 Halogen 

lamp

•

  Power supply PCB

6F

Heater hard limiter operates.

•

 Thermistor 

ASSY

•

  Power supply PCB

71

Scanner motor does not synchronize with
the reference clock.

•

 Scanner 

motor

72

Cannot detect Beam Detect signal.

•

 Scanner 

motor

•

  MP tray open sensor

Summary of Contents for DCP-8040
















































































































































































































































































































































































Reviews:

No comments

Related manuals for DCP-8040

Canon imagePROGRAF iPF8400 Basic Manual preview
imagePROGRAF iPF8400
Brand: Canon Pages: 157
Canon JX210P On-Screen Manual preview
JX210P
Brand: Canon Pages: 91
olympia electronics A-200 Manual preview
A-200
Brand: olympia electronics Pages: 4
Xerox Phaser 6180MFP Installation Manual preview
Phaser 6180MFP
Brand: Xerox Pages: 2
Xerox Phaser 6180MFP Features Setup Manual preview
Phaser 6180MFP
Brand: Xerox Pages: 103
Xerox Phaser 6125 Specification preview
Phaser 6125
Brand: Xerox Pages: 2
Xerox DocuPrint 4850 NPS Troubleshooting Manual preview
DocuPrint 4850 NPS
Brand: Xerox Pages: 68
Xerox DocuColor 7002 Quick Start Manual preview
DocuColor 7002
Brand: Xerox Pages: 28
Xerox DocuColor 5000AP User Manual preview
DocuColor 5000AP
Brand: Xerox Pages: 5
Xerox Document WorkCentre 450c User Manual preview
Document WorkCentre 450c
Brand: Xerox Pages: 214
Xerox DocuColor 5750 System Administration Manual preview
DocuColor 5750
Brand: Xerox Pages: 68
Xerox DocuColor 1632 Quick Connect Manual preview
DocuColor 1632
Brand: Xerox Pages: 2
Xerox PHASER 6140 User Manual preview
PHASER 6140
Brand: Xerox Pages: 170
Xerox Phaser 5500 series Setup Manual preview
Phaser 5500 series
Brand: Xerox Pages: 2
Xerox PHASER 6121MFP User Manual preview
PHASER 6121MFP
Brand: Xerox Pages: 238
Xerox DOCUCOLOR 12 Getting To Know Manual preview
DOCUCOLOR 12
Brand: Xerox Pages: 24
Xerox DOCUCOLOR 12 Supplement Manual preview
DOCUCOLOR 12
Brand: Xerox Pages: 18
Xerox DocuColor 240 Evaluator Manual preview
DocuColor 240
Brand: Xerox Pages: 18

Brands by name

Popular brands

Load more brands