Brother DCP-8040 Service Manual Download

Page: 24 / 367

MFC-8440/8840D/8840DN, DCP-8040/8045D/8045DN

SERVICE MANUAL

1-11

CAUTION:

When you are choosing print media, be sure to follow the information given below to prevent
any paper jams, print quality problems or machine damage;

•

It is recommended to use long-grained paper for the best print quality. If short-grained
paper is being used, it might be the cause of paper jams.

•

Use neutral paper. Do not use acid paper to avoid any damage to the drum unit.

•

Avoid using coated paper such as vinyl coated paper.

•

Avoid using preprinted or highly textured paper.

•

It is recommended to use labels or transparencies which are designed for use in laser
printers.

•

Avoid feeding labels with the carrier sheet exposed, or the machine will be damaged.

•

Before loading paper with holes such as organizer sheets, be sure to fan the stack well.

•

Do not use organizer sheets that are stuck together. The glue that is used might caused
damaged to the machine.

•

When printing on the back of pre-printed paper, if the paper is curled, be sure to straighten
the paper as much as possible.

•

Different types of paper should not be loaded at the same time in the paper tray to avoid
any paper jams or misfeeds.

2.13 Printable

Area

2.13.1 PCL5e/EPSON/IBM

emulation

The figure below shows the printable area each emulation guarantees when printing on Portrait
and Landscape.

Portrait

Physical page

Printable area

Logical page

Physical page length

Maximum logical page length

Distance from edge of physical page to
edge of logical page

Summary of Contents for DCP-8040
















































































































































































































































































































































































Search results

Summary of Contents for DCP-8040

Reviews:

Related manuals for DCP-8040

Brands by name

Popular brands

Brother DCP-8040, Service Manual

Search results

Summary of Contents for DCP-8040

Reviews:

Related manuals for DCP-8040

Brands by name

Popular brands