manualshive.com logo in svg

Brother DCP-8040, Service Manual

The Brother DCP-8040 is a versatile multifunction printer that offers high-quality printing, scanning, and copying capabilities. With its advanced features and user-friendly interface, this efficient device is perfect for both home and office use. Download the free brochure & specs manual from 88.208.23.73:8080 to explore all the functionalities of this exceptional printer.

Share
Download
background image

MFC-8440/8840D/8840DN, DCP-8040/8045D/8045DN 

SERVICE MANUAL 

A-69

 

APPENDIX  5     LOCATION TO ATTACH THE ADDITIONAL RIBS 

The additional ribs are recommended to attach in order to prevent a damage towards ribs of 
the Joint cover ASSY ZL2E caused by printing with the particular kind of paper.  With the 
additional ribs, it prevents paper jams when the particular kind of paper ejects as well.  There 
are 2 types of ribs; Top cover rib and Top cover rib2.  It is necessary to be careful about the 
two sides of location to attach the additional ribs properly as the figure below. 

 

NOTE: 
Pay attention to the location circled by red color dotted line to attach the additional ribs against 
the ribs of the Joint cover ASSY ZL2E. 

Joint cover ASSY ZL2E 

Top cover rib 

Top cover rib2 

Top cover rib2 

Top cover rib 

Adhesive tape 

Adhesive tape 

Summary of Contents for DCP-8040
















































































































































































































































































































































































Reviews:

No comments

Related manuals for DCP-8040

NCR 7197 Manual preview
7197
Brand: NCR Pages: 10
Xerox Document WorkCentre 480cx User Manual preview
Document WorkCentre 480cx
Brand: Xerox Pages: 318
Xerox Phaser 3010 User Manual preview
Phaser 3010
Brand: Xerox Pages: 76
Xerox ColorQube 9301 Quick Manual preview
ColorQube 9301
Brand: Xerox Pages: 11
Xerox ColorQube 9303 User Manual preview
ColorQube 9303
Brand: Xerox Pages: 352
Xerox Color 560 Printer Specification Sheet preview
Color 560 Printer
Brand: Xerox Pages: 2
Xerox B1022 System Administrator Manual preview
B1022
Brand: Xerox Pages: 105
Xerox AltaLink B8145 Manual preview
AltaLink B8145
Brand: Xerox Pages: 42
Xerox AltaLink B8145 Getting Started Manual preview
AltaLink B8145
Brand: Xerox Pages: 13
Xerox D110 Manual preview
D110
Brand: Xerox Pages: 132
Xerox CopyCentre C2128 Product Safety Data Sheet preview
CopyCentre C2128
Brand: Xerox Pages: 2
Xerox Legacy 4112 User Manual Supplement preview
Legacy 4112
Brand: Xerox Pages: 20
Xerox Legacy 4112 Quick Start Manual preview
Legacy 4112
Brand: Xerox Pages: 34
Xerox 700i Specification preview
700i
Brand: Xerox Pages: 8
Xerox 4890 Advanced Troubleshooting Manual preview
4890 Advanced
Brand: Xerox Pages: 70
Xerox Nuvera 100 Installation Planning Manual preview
Nuvera 100
Brand: Xerox Pages: 124
Xerox Nuvera 100 Quick Reference preview
Nuvera 100
Brand: Xerox Pages: 2
Xerox Nuvera 100 Planning Manual preview
Nuvera 100
Brand: Xerox Pages: 20

Brands by name

Popular brands

Load more brands