Brother DCP-8040 Service Manual Download | Manualshive

Page: 33 / 367

background image

CHAPTER 2 INSTALLATION AND BASIC OPERATION

2-2

2. UNPACKING

When unpacking the machine, check to see that all of the following components are included
in the carton.

Quick Setup Guide

CD-ROMs

For Windows (1 piece)

®

For Macintosh (1 piece)

®

User's Guide

ADF Support

Drum Unit Assembly

AC Power Cord

Telephone

Line Cord

Test Sheet

(U.S.A. only)

(U.S.A./Canada only)

(including Toner Cartridge)

Accessory Order Form

4

3

1

1. Control Panel
2. Face-down Output Tray
Support Flap (Support Flap)
3. Manual Feed Tray
(For MFC-8440, DCP-8040)
Multi-purpose Tray (MP Tray)
(For MFC-8840D/8840DN, DCP-8045D/8045DN)

4. Paper Tray
5. Front Cover
6. Power Switch
7. Document Cover
8. Automatic Document Feeder (ADF)

2

MFC

5

6

7

8

Fig. 2-1

Carton components may differ from one country to another.

Save all packing materials and the carton.

NOTE:

•

The interface cable is not a standard accessory. Please purchase the appropriate
interface cable for the interface you intend to use (Parallel or USB).

•

For Parallel use a bi-directional shield interface cable that is IEEE 1284-compliant, and not
longer than 6 feet (2 meters).

•

For USB: use a Hi-Speed USB 2.0 interface cable that is not longer than 6 feet (2 meters).

•

Please make sure that you use a Hi-Speed USB 2.0 certified cable if your computer uses
a Hi-Speed USB 2.0 interface.

•

Even if your computer has a USB 1.1 interface, you can connect the machine.

«
...
31
32
33
34
35
...
»

Summary of Contents for DCP-8040
















































































































































































































































































































































































Reviews:

No comments

Related manuals for DCP-8040

Brand: Panasonic Pages: 32

Brand: Oki Pages: 16

Brand: Olivetti Pages: 179

Brand: Olivetti Pages: 36

Brand: Oki Pages: 679

Brand: Oki Pages: 40

Brand: OKIDATA Pages: 308

Brand: OKIDATA Pages: 9

Brand: OKIDATA Pages: 2

Microline 8480 FB

Brand: Oki Pages: 12

Brand: Canon Pages: 4

Brand: GE Pages: 16

Brand: KIP Pages: 103

DocuPrint 4850 NPS

Brand: Xerox Pages: 276

Brand: Triumph Adler Pages: 4

Brand: Tandy Pages: 83

Brand: Panduit Pages: 85

Brand: SNBC Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands