V
- 20
WSW07
(Dial tone setting 1)
Selector
No.
Function
Setting and Specifications
1
2
Frequency band range
No. 1 2
0 0
: Narrows by 10 Hz
0 1
: Initial value
1 X
: Widens by 10 Hz
3
Line current detection
0: No
1: Yes
4
|
6
2nd dial tone detection level
(Z = 600
Ω
)
No. 4 5 6
0
0 0 : -21 dBm
0
0 1 : -24 dBm
0
1 0 : -27 dBm
0
1 1 : -30 dBm
1
0 0 : -33 dBm
1
0 1 : -36 dBm
1
1 0 : -39 dBm
1
1 1 : -42 dBm
7
1st dial tone interrupt detecting
time
0: 30 ms
1: 50 ms
8
Not used.
NOTE:
The WSW07 is not applicable in those countries where no dial tone or line current detection is
supported, e.g., U.S.A.
l
Selectors 1 and 2: Frequency band range
These selectors set the frequency band for the 1st dial tone and the busy tone (before dialing) to be
detected.
This setting is effective only when selectors 1 through 3 of WSW05 are set to “1,1,1.”
l
Selector 3:
Line current detection
This selector determines whether or not the equipment should detect a line current before starting
dialing.
l
Selectors 4 through 6:
2nd dial tone detection level
These selectors set the detection level of the 2nd dial tone.
l
Selector 7:
1st dial tone interrupt detecting time
This selector sets the allowable time length of an interrupt which should not be interpreted as an
interrupt in the 1st dial tone dialing.
Summary of Contents for FAX 750
