Brother HL-1070 Service Manual Download | Manualshive

Page: 15 / 244

background image

I-9

3. SAFETY

INFORMATION

3.1

Laser Safety (110 - 120V Model only)

This printer is certified as a Class 1 laser product under the US Department of Health and
Human Services (DHHS) Radiation Performance Standard according to the Radiation
Control for Health and Safety Act of 1968. This means that the printer does not produce
hazardous laser radiation.

Since radiation emitted inside the printer is completely confined within the protective
housings and external covers, the laser beam cannot escape from the machine during
any phase of user operation.

3.2

FDA Regulations (110 - 120V Model only)

The US Food and Drug Administration (FDA) has implemented regulations for laser
products manufactured on and after August 2, 1976. Compliance is mandatory for
products marketed in the United States. One of the following labels on the back of the
printer indicates compliance with the FDA regulations and must be attached to laser
products marketed in the United States.

The label for Japanese manufactured products

The label for US manufactured products

MANUFACTURED:
BROTHER INDUSTRIES, LTD.

15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467, Japan.
This product complies with FDA radiation
performance standards, 21 CFR Subchapter J.

MANUFACTURED:
BROTHER INDUSTRIES (USA) INC.

2950 Brother Blud., Bartlet, TN 38133, U.S.A.
This product complies with FDA radiation
performance standards, 21 CFR Subchapter J.

Download Free Service Manual and Resetter Printer at http://printer1.blogspot.com

«
...
13
14
15
16
17
...
»

Summary of Contents for HL-1070





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070

Brand: Panasonic Pages: 32

Brand: Samsung Pages: 322

Brand: Samsung Pages: 340

Brand: Samsung Pages: 349

Brand: Samsung Pages: 330

Brand: Samsung Pages: 315

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 232

Brand: Samsung Pages: 42

SCX-6545N Series

Brand: Samsung Pages: 468

Brand: Samsung Pages: 196

SCX4521F - B/W Laser - All-in-One

Brand: Samsung Pages: 120

Brand: DataCard Pages: 2

Brand: Oki Pages: 215

WorkCentre Pro 90

Brand: Xerox Pages: 36

Brand: Oce Pages: 306

Brand: Printek Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands