Brother HL-1070 Service Manual Download | Manualshive

Page: 150 / 244

background image

- 20 -

Using the Printer Status Monitor Program

Type

C:\RPCX>STMX

and press the Enter key to make the Printer Status Monitor Program

stay resident in your computer memory. If there are any changes to the printer status, it
displays a message on your computer screen.

If the printer status monitor program stays resident in your computer, you can monitor the
printer status on your computer screen immediately using the hot-key sequence (Ctrl+Alt+R).

To remove the Printer Status Monitor program from your computer memory, type

C:\RPCX>STMX/R

and press the Enter key.

❏

The RPC works in the environment where your printer is directly connected to your
computer. If you are using any printer buffer switches which do not support bi-directional
communication between the printer and computer, the program works only in the PC to
printer direction and cannot receive printer status information.

❏

The program does not work with printers on a network.

❏

If the RPC conflicts with some application software, exit your application software and
then run the RPC.

❏

The RPC may work in the DOS-compatible box screen mode of Windows, however, it is
recommended that you completely exit from Windows to the DOS prompt before using the
RPC.

❏

The Printer Status Monitor and some other Terminate-and-Stay programs cannot coexist in
the computer’s memory. If they do not work properly together, use them one at a time.
You can suspend the Printer Status monitor with any of the following methods or
commands.

Type

C:\RPCX>STMX/R

and press the Enter key.

Hold the space bar down while executing the AUTOEXEC.BAT file at DOS startup to
prevent the status monitor being loaded as a TSR program.

«
...
148
149
150
151
152
...
»

Summary of Contents for HL-1070





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070

Pixma MG2400 Series

Brand: Canon Pages: 2

Brand: DataCard Pages: 2

Jetprinter Disney Edition Z615 Series

Brand: Lexmark Pages: 2

DC240 - DocuColor 240 Color Laser

Brand: Xerox Pages: 2

ColourLaser series guide

Brand: Xante Pages: 31

Brand: Xante Pages: 31

Accel-a-Writer 812

Brand: Xante Pages: 12

7760DN - Phaser Color Laser Printer

Brand: Xerox Pages: 158

Brand: Z Corporation Pages: 76

VersaLink C400V

Brand: Xerox Pages: 196

Brand: Oki Pages: 336

Perfecta 2400STP

Brand: Variquest Pages: 12

apeosport 550 I

Brand: Xerox Pages: 160

Brand: Canon Pages: 769

Brand: Epson Pages: 4

Brand: Roland Pages: 6

Brand: WOOSIM Pages: 27

Brand: FARGO electronics Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands