Brother HL-1070 Service Manual Download | Manualshive

Page: 161 / 244

background image

USER’S GUIDE

Radio Interference (220-240 V Model Only)

This printer complies with EN55022(CISPR Publication 22)/Class B.

Before this product is used, ensure that you use a double-shielded cable with twisted-
pair conductors and that it is marked “IEEE 1284 compliant”. The cable must not
exceed 1.8 meters in length.

Laser Safety (For 110–120 V Model Only)

This printer is certified as a Class I laser product under the U.S. Department of Health and
Human Services (DHHS) Radiation Performance Standard according to the Radiation Control
for Health and Safety Act of 1968. This means that the printer does not produce hazardous
laser radiation.

Since radiation emitted inside the printer is completely confined within protective housings
and external covers, the laser beam cannot escape from the machine during any phase of user
operation.

FDA Regulations (For 110-120 V Model Only)

U.S. Food and Drug Administration (FDA) has implemented regulations for laser products
manufactured on and after August 2, 1976. Compliance is mandatory for products marketed
in the United States. One of the following labels on the back of the printer indicates
compliance with the FDA regulations and must be attached to laser products marketed in the
United States.

MANUFACTURED:
BROTHER INDUSTRIES (USA) INC.
2950 Brother Blvd., Bartlett, TN 38133, U.S.A.
This product complies with FDA radiation performance standards, 21 CFR Subchapter J

MANUFACTURED:
BROTHER INDUSTRIES LTD.
15-1 Naeshiro-cho Mizuho-ku Nagoya, 467-8561 Japan
This product complies with FDA radiation performance standards, 21 CFR Subchapter J

Caution

Use of controls, adjustments or performance of procedures other than those specified in this
manual may result in hazardous radiation exposure.

«
...
159
160
161
162
163
...
»

Summary of Contents for HL-1070





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070

Brand: Canon Pages: 11

imageRUNNER ADVANCE 8085

Brand: Canon Pages: 176

Brand: Canon Pages: 85

imageRUNNER 5070

Brand: Canon Pages: 4

imageRUNNER 5570

Brand: Canon Pages: 4

IMAGERUNNER 7095 PRINTER

Brand: Canon Pages: 8

IMAGERUNNER 7105

Brand: Canon Pages: 21

Brand: Canon Pages: 58

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 12

imageRUNNER ADVANCE C2020

Brand: Canon Pages: 68

imageRUNNER ADVANCE 6055

Brand: Canon Pages: 134

Color imageRUNNER LBP5970

Brand: Canon Pages: 67

FAXPHONE L170 - B/W Laser - Copier

Brand: Canon Pages: 12

Brand: Canon Pages: 2

imageRunner 1133

Brand: Canon Pages: 60

Color imageCLASS MF8280Cw

Brand: Canon Pages: 36

Brand: Canon Pages: 104

imagePROGRAF iPF8300

Brand: Canon Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands