manualshive.com logo in svg

Brother HL-1070, Service Manual

The Brother HL-1070 Parts Reference List manual is a valuable resource for troubleshooting and repairing your printer. You can easily download this comprehensive guide for free from our website, ensuring you have quick access to the information you need.

Share
Download
background image

CHAPTER 3 CONTROL PANEL

3–3

Alarm Lamp

The 

Alarm

 lamp blinks to indicate a printer error status such as “Cover

Open” and “Memory Full.” If any other error occurs, the printer indicates
the error by blinking the 

Alarm

 lamp with another lamp or by printing an

error report.

✒

Note

The 

Ready

, 

Data

 and 

Drum

 lamps are used to indicate printer errors

with the Alarm lamp. See 

“ALARM INDICATIONS AT A GLANCE”

 in

Chapter 6 and take corrective action for the error.

Switch

This 

switch

 will be used as the following purpose depending on the

situation.

Cancel Printing

If you press the 

switch

 during printing, the printer immediately stops

printing and ejects the paper.

Wake-up

If the printer is in sleep mode, pressing the 

switch

 wakes it up into the

ready state.

Form Feed

If the 

Data

 lamp is on, press the 

switch

. The printer prints any data

remaining in the printer memory: this operation is called “Form Feed.”

Error Recover

If an error occurs, the printer will recover from some errors
automatically. If the error does not clear automatically, press the 

switch

 to

clear the error and continue printer operation.

Select Feeder

If the 

Ready

 lamp is on, press the 

switch

. You can select Feeder 1 or

Feeder 2.

Summary of Contents for HL-1070





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070

Canon image Prograf iPF785 Series Basic Manual preview
image Prograf iPF785 Series
Brand: Canon Pages: 136
GBC A1 Operation & Instruction Manual preview
A1
Brand: GBC Pages: 110
Xerox M Series Initial Setup Card preview
M Series
Brand: Xerox Pages: 2
EasyThreed Mars Quick Start Manual preview
Mars
Brand: EasyThreed Pages: 15
Oce sx1481 User Manual preview
sx1481
Brand: Oce Pages: 192
Oce OP20 Operation Manual preview
OP20
Brand: Oce Pages: 22
Oce FX3000 SERIES Quick Setup Manual preview
FX3000 SERIES
Brand: Oce Pages: 41
Oce fx2081 Installation Manual preview
fx2081
Brand: Oce Pages: 28
Oce im5530 Specifications preview
im5530
Brand: Oce Pages: 6
QMS 2560 Options Installation preview
2560
Brand: QMS Pages: 104
Oce im2330 Printing Manual preview
im2330
Brand: Oce Pages: 386
Oce im2330 Specifications preview
im2330
Brand: Oce Pages: 2
Oce cm2520 Safety Information & Getting Started preview
cm2520
Brand: Oce Pages: 27
Oce im2330 Operator'S Manual preview
im2330
Brand: Oce Pages: 324
Radio Shack TRS-80 Operation Manual preview
TRS-80
Brand: Radio Shack Pages: 57
Ultimaker 2 Extended User Manual preview
2 Extended
Brand: Ultimaker Pages: 30
µ-Dimension BST 1200es User Manual preview
BST 1200es
Brand: µ-Dimension Pages: 74
Fuji Xerox ApeoSport C5540I Quick Reference Manual preview
ApeoSport C5540I
Brand: Fuji Xerox Pages: 108

Brands by name

Popular brands

Load more brands