Brother HL-1070 Service Manual Download

Page: 233 / 244

APPENDIX

A–3

Electrical and Mechanical

Power Source

U.S.A. and Canada:

AC 110 to 120 V, 50 / 60 Hz

Europe and Australia:

AC 220 to 240 V, 50 Hz

Power Consumption

Printing:

280 W or less

Stand-by:

60 W or less

Sleep:

13 W or less

Noise

Printing:

49 dB A or less

Stand-by:

38 dB A or less

Temperature

Operating:

10 to 32.5°C (50 to 90.5°F)

Storage:

0 to 40°C (38 to 104°F)

Humidity

Operating:

20 to 80% (without condensation)

Storage:

10 to 85% (without condensation)

Dimensions (W x D x H)

402 x 439 x 274 mm (15.8 x 17.3 x 10.8 inches)
(when the output tray is closed.)

Weight

Approx. 9.6 kg (21.2 lb.) including the drum unit and toner
cartridge

Summary of Contents for HL-1070





















































































































































































































































Search results

Summary of Contents for HL-1070

Reviews:

Related manuals for HL-1070

Brands by name

Popular brands

Brother HL-1070, Service Manual

Search results

Summary of Contents for HL-1070

Reviews:

Related manuals for HL-1070

Brands by name

Popular brands