background image

3 - 46

Needle-presser unit

Main unit

11 

Needle bar assy. attachment

1. Insert the needle bar assy. 

1

 from the bottom of the needle holder assy.,

and then insert the needle bar block 

2

 and the needle thread block 

3

through the needle bar assy. and then through to the upper hole. 

*Key point

• Insert the needle bar block 

2

 and the needle thread block 

3

 

so that the shaft of the needle bar block 

2

 is on the right side 

and the tab of the needle thread block 

3

 is on the left side. 

2

3

1

11-1 

Needle bar assy. assembly

1. Attach the presser feed holder assy. 

1

 to the needle bar assy. 

2

 with the

screw 

1

.

*Key point

• The screw 

1

 should be on the right side when the groove on 

the needle bar assy. 

2

 faces the front. 

1

1

2

1

Needle Clamp Screw

12 

Thread take-up lever link attachment

1. Insert the shaft 

1

 into the base holder 

2

, and then align the screw 

1

 with

the trench on the base holder 

2

, and tighten it temporarily.

2. Attach the thread take-up lever link 

3

3. Apply a light covering of MOLYKOTE EM-30L to the circumference of

the shaft within 10 mm of the retaining ring.

4. Insert the spring washer 

4

 into the shaft 

1

5. Attach the retaining ring (E5) to the groove on the shaft 

1

.

Apply MOLYKOTE EM-30L to the circumference of the 
shaft within 10 mm of the retaining ring.

Light covering

XC8385***

1

Torque

Hand tighten

1

3

4

Retaining ring E5

1

1

2

Screw

M3X8

Summary of Contents for HS-3000





































































































































































Reviews: