manualshive.com logo in svg

Brother MFC-9420CN, Service Manual

The Brother MFC-9420CN is a versatile all-in-one printer that combines printing, scanning, and copying functionalities. Its Service Manual is available for free download on 88.208.23.73:8080, providing detailed instructions and troubleshooting guidance to ensure optimal performance of this high-quality device.

Share
Download
background image

 App. 

4-41 

Confidential

 

 

Selectors 6 through 8:  Extension of incoming calling signal (CI) frequency band specified by 

selectors 1 through 4 on WSW14 

At the start of reception, if the machine detects the frequency of a CI signal specified by selectors  

1 through 4 on WSW14, it starts the ringer sounding.  However, the machine may fail to detect the  

CI signal normally due to noise superimposed at the time of reception.  To prevent it, use selectors  

6 through 8 on WSW36. 

If the machine detects higher frequencies than the setting made here, it regards them as noise and  

interprets the detecting state as being normal, allowing the ringer to keep sounding according to  

the preset number of ringers (until it starts automatic reception of FAX data in the FAX mode or  

enters the TAD mode in the TEL mode). 

 

 

WSW37 

(Function setting 15)

 

Selector 

No. 

Function 

Setting and Specifications 

1 

Printout of the stored image 

data of an unsent document 

onto an error report 

 0: 

No 

1: 

Yes 

2 

Erasure of the stored image 

data of an unsent document at 

the time of the subsequent in-

memory message transmission 

 0: 

No 

1: 

Yes 

3 

| 

8 

Not used. 

 

 

  Selector 1: 

Printout of the stored image data of an unsent document onto an error report 

This selector determines whether or not to print out the 1st-page image data of a document onto  
the error report if the document image data stored in the temporary memory cannot be transmitted  
normally. 

  Selector 2: 

Erasure of the stored image data of an unsent document at the time of the subsequent 
in-memory message transmission 

If in-memory message transmission fails repeatedly when selector 1 is set to "1," the temporary  
memory will be occupied with image data.  Setting selector 2 to "1" will automatically erase the  
stored 1st-page image data of an unsent document at the time of the subsequent in-memory  
message transmission only when recording paper or toner runs out. 

 

Summary of Contents for MFC-9420CN













































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MFC-9420CN

TallyGenicom T6212 Operator'S Manual preview
T6212
Brand: TallyGenicom Pages: 92
Oce im4511 Operation Manual preview
im4511
Brand: Oce Pages: 8
Xerox C410 User Manual preview
C410
Brand: Xerox Pages: 262
Oki B8300 User Manual preview
B8300
Brand: Oki Pages: 95
Canon Pixma TS7700i Series Manual preview
Pixma TS7700i Series
Brand: Canon Pages: 554
Xerox WorkCentre 7328 Brochure & Specs preview
WorkCentre 7328
Brand: Xerox Pages: 8
Telpar MTP-2222 User Manual preview
MTP-2222
Brand: Telpar Pages: 52
Konica Minolta IC-206 User Manual preview
IC-206
Brand: Konica Minolta Pages: 424
Riso HC5500T User Manual preview
HC5500T
Brand: Riso Pages: 66
Star Micronics SP500 Series Technical Manual preview
SP500 Series
Brand: Star Micronics Pages: 73
Canon imageRUNNER ADVANCE C255i Getting Started preview
imageRUNNER ADVANCE C255i
Brand: Canon Pages: 16
Canon imageRUNNER ADVANCE C9075S PRO Customer Expectation Document preview
imageRUNNER ADVANCE C9075S PRO
Brand: Canon Pages: 56
Canon imageRUNNER ADVANCE C9065S PRO Service Manual preview
imageRUNNER ADVANCE C9065S PRO
Brand: Canon Pages: 86
Canon imageRUNNER ADVANCE C7565i II Advance Maintenance Manual preview
imageRUNNER ADVANCE C7565i II
Brand: Canon Pages: 24
Canon imageRUNNER ADVANCE C5235 Basic Operation Manual preview
imageRUNNER ADVANCE C5235
Brand: Canon Pages: 208
Canon imageRUNNER ADVANCE DX User Manual preview
imageRUNNER ADVANCE DX
Brand: Canon Pages: 47
Canon imageRUNNER ADVANCE C250i Maintenance Manual preview
imageRUNNER ADVANCE C250i
Brand: Canon Pages: 42
Canon IMAGERUNNER ADVANCE C5051 Brochure & Specs preview
IMAGERUNNER ADVANCE C5051
Brand: Canon Pages: 6

Brands by name

Popular brands

Load more brands