background image

19

c

Touch the “Start” key to start cutting.

Memo

• When the roll feeder is used, half-cutting is automatically 

turned on.

When cutting is finished, the following screen appears.

Check the results of trial cutting.
For details, see “Checking the Trial Cutting Results” on page 19.
• To start cutting the pattern for your project, press the “Start” 

key.
When cutting is finished, see step 

g

 in “Cutting” on page 16.

• To perform trial cutting again, press the “Test again” key.

For details, see “Changing the Cut Pressure Setting” on 
page 19.

• To perform trial feeding, press 

.

For details, see “Trial Feeding” on page 20.

Checking the Trial Cutting Results

Adjust the cutting pressure according to the trial cutting results.
Repeatedly perform trial cutting and adjust the cutting pressure until 
the material is cut cleanly.

Note

• If the blade penetrates the material, faint cut marks may 

remain on the machine's surface where the blade makes 
contact (

1

). In that case, cutting may no longer be 

performed correctly. Contact Brother Customer Service or 
Brother authorized service center.

Appropriate cutting pressure

The appropriate cutting pressure is when the surface layer of 
the material is cut cleanly and the backing paper is not cut.

Memo

The hook of the spatula and hook set (CASPHK 1) is useful 
for peeling off the half-cut material from the backing paper 
or backing film. To purchase the spatula and hook set 
(CASPHK 1), contact the retailer where this product was 
purchased.

Changing the Cut Pressure Setting

The appropriate cutting pressure for half-cuts is automatically set; 
however, some types of material may not be cut cleanly.
If the material could not be cut cleanly, refer to the following table, 
and adjust the setting for the cutting pressure. Since the blade may 
penetrate the material, perform trial cutting after each time that the 
setting is increased.

Changing the cut pressure setting

a

When the following screen appears after trial cutting is 
finished, touch the “Test again” key to display the test 
screen.

b

Touch 

 to move the test pattern to a different 

location. The test pattern can also be moved by dragging 
it in the screen.

a

Trial cutting result

Adjustment

Part of the pattern is 
not cut.

Pressure too light: Touch 

 

in the settings screen once to 
increase the pressure.

The entire pattern is 
not cut.

Pressure too light: Touch 

 

in the settings screen once to 
increase the pressure.

There are deep cuts 
completely through 
the backing paper.

Pressure too strong: Touch 

 in the settings screen once 

to decrease the pressure.

Summary of Contents for ScanNCut DX







































Reviews: