Brunswick Black Wolf Pro Installation Manual Download

Page: 4 / 15

PAGE 4

BRUNSWICK INSTALLATION MANUAL

BLACK WOLF PRO

BASE FRAME AND LEG ASSEMBLY
(CONTINUED)

FIGURE THREE

Step #4:

Loosely attach the four leg attach brackets to

the top of the legs with 3/8-16 x 1”-1/2” hex head screws
and 3/8 at washers.

FIGURE THREE

FIGURE FOUR

Step #7:

Loosely attach the two side sills to the two end

sills and two cross supports with 5/16-18 x 3” hex head
screws, 5/16 at washers and 5/16-18 threaded nut
plates.

Step #8:

Securely attach the two slate attach cleats to

each end sill with 5/16-18 x 4-1/2” hex head screws, 5/16
at washers and 5/16 -18 hex nuts.

FIGURE FIVE

3/8 WASHER

3/8-16 X 1-1/2”

HEX HEAD CAP

SCREW

LEG ATTACH

BRACKETS

(4 PLCS.)

5/16-18
THREADED
NUT PLATE

5/16-18

THREADED

NUT PLATE

5/16-18 x 3”

HEX HEAD SCREW

5/16 FLAT WASHER

5/16-18 x 4-1/2”
HEX HEAD SCREW

5/16 FLAT WASHER

5/16 FLAT
WASHER

5/16-18

HEX NUT

CROSS SUPPOR

SIDE SILL

END SILL

CROSS SUPPOR

END SILL

SIDE SILL

5/16 WASHER

5/16-18 x 3”

HEX HEAD SCREW

Summary of Contents for Black Wolf Pro
















Search results

Summary of Contents for Black Wolf Pro

Reviews:

Related manuals for Black Wolf Pro

Brands by name

Popular brands

Brunswick Black Wolf Pro, Installation Manual

Search results

Summary of Contents for Black Wolf Pro

Reviews:

Related manuals for Black Wolf Pro

Brands by name

Popular brands