Brunswick Black Wolf Pro Installation Manual Download

Page: 5 / 15

BRUNSWICK INSTALLATION MANUAL

PAGE 5

BLACK WOLF PRO

BASE FRAME AND LEG ASSEMBLY
(CONTINUED)

FIGURE FIVE

Step #9:

Carefully lower base frame over the legs and leg

brackets.

Step #10:

Align clearance holes in attach brackets with

clearance holes in the side sills and attach securely with
3/8-16 x 3” hex head cap screw, 3/8 at washers and 3/8-
16 hex nuts.

Step #11:

Securely tighten all base frame hardware,

making sure that all top surfaces are ush.

Step #12:

Drop Pocket Table Only: Attach the triangle

Step #13:

Attach two bridge rack brackets to the base

frame side sill, with #10 x 3/4” pan head screws.

FIGURE FIVE

Pilot holes provided.

brackets to the designated foot end base frame sill using
four #10 x 3/4” pan head screws and #6 fender washers,
pilot holes are provided.

Gully Pocket Table Only: Install four 1/4-20UNC tee-nuts
into the mounting holes for the receiver box attachment.
Tee-nuts will need to be installed on the exterior face of the
designated foot end base frame sill with a hammer.

3/8-16 x 3” HEX HEAD CAP SCREW

3/8 FLAT WASHER

3/8-16 HEX NUT

3/8 FLAT WASHER

BRIDGE RACK BRACKET

#6 FENDER WASHER

#10 X 3/4”
PAN HEAD SCREW

TRIANGLE BRACKET

#10 X 3/4”
PAN HEAD
SCREW

BRIDGE RACK
BRACKET

#6 FENDER
WASHER

#10 X 3/4”
PAN HEAD
SCREW

TRIANGLE
BRACKET

#10 X 3/4”
PAN HEAD
SCREW

1/4-20UNC T-NUT

1/4-20UNC TEE-NUT

Summary of Contents for Black Wolf Pro
















Search results

Summary of Contents for Black Wolf Pro

Reviews:

Related manuals for Black Wolf Pro

Brands by name

Popular brands

Brunswick Black Wolf Pro, Installation Manual

Search results

Summary of Contents for Black Wolf Pro

Reviews:

Related manuals for Black Wolf Pro

Brands by name

Popular brands