Bryant 912S Installation, Operating And Service Instructions Download

Page: 41 / 85

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each appliance

connected to the venting system being placed into operation

could result in carbon monoxide poisoning or death.
The following steps shall be followed for each appliance

connected to the venting system being placed into operation,

while all other appliances connected to the venting system are

not in operation:

1. Seal any unused openings in venting system.
2. Inspect the venting system for proper size and

horizontal pitch, as required in the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the CSA B149 Nat-

ural Gas and Propane Installation Code and these in-

structions. Determine that there is no blockage or

restriction, leakage, corrosion and other deficiencies,

which could cause an unsafe condition.

3. As far as practical, close all building doors and

windows and all doors between the space in which the

appliance(s) connected to the venting system are

located and other spaces of the building.

4. Close fireplace dampers.
5. Turn on clothes dryers and any appliance not

connected to the venting system. Turn on any exhaust

fans, such as range hoods and bathroom exhausts, so

they are operating at maximum speed. Do not operate

a summer exhaust fan.

6. Follow the lighting instructions. Place the appliance

being inspected into operation. Adjust the thermostat

so appliance is operating continuously.

7. Test for spillage from draft hood equipped appliances

at the draft hood relief opening after 5 minutes of

main burner operation. Use the flame of a match or

candle.

8. If improper venting is observed during any of the

above tests, the venting system must be corrected in

accordance with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54 and/or CSA B149.1 Natural Gas

and Propane Installation Code.

9. After it has been determined that each appliance

connected to the venting system properly vents when

tested as outlined above, return doors, windows,

exhaust fans, fireplace dampers and any other

gas

−

fired burning appliance to their previous

conditions of use.

WARNING

General

If this furnace replaces a furnace that was connected to a vent

system or chimney, the vent or vent connectors of other remaining

appliances may need to be re

−

sized. Vent systems or vent

connectors of other appliances must be sized to the minimum size

as determined using appropriate table found in the current edition

of National Fuel Gas Code NFPA 54/ANSI Z

−

223.1. In Canada,

refer to CAN/CSA

−

B149.1.

An abandoned masonry chimney may be used as a raceway for

properly insulated and supported combustion

−

air (when

applicable) and vent pipes. Each furnace must have its own set of

combustion

−

air and vent pipes and be terminated individually, as

shown in Fig. 54 for Direct Vent (2

−

Pipe) system, or Fig. 55 for

single

−

pipe or ventilated combustion air option.

A furnace shall not be connected to a chimney flue serving a

separate appliance designed to burn solid fuel.

Other gas appliances with their own venting system may also use

the abandoned chimney as a raceway providing it is permitted by

local code, the current edition of the National Fuel Gas Code, and

the vent or liner manufacturer’s installation instructions. Care must

be taken to prevent the exhaust gases from one appliance from

contaminating the combustion air of other gas appliances.
Do not take combustion air from inside the chimney when using

ventilated combustion air or single

−

pipe vent option.

These furnaces can be vented as direct

−

vent (two

−

pipe), ventilated

combustion air or non-direct (single

−

pipe) vent system. Each type

of venting system is described below. Common venting between

these furnaces or other appliances is prohibited.

Materials

U.S.A.

Combustion air and vent pipe, fittings, primers, and solvents must

conform to American National Standards Institute (ANSI)

standards and American Society for Testing and Materials (ASTM)

standards. See Table 15 for approved materials for use in the

U.S.A. This furnace is also CSA approved for venting with M&G

DuraVent

PolyPro

polypropylene venting systems.

Canada

Special Venting Requirements for Installations in Canada,

Installation in Canada must conform to the requirements of

CAN/CSA B149 code. Vent systems

must

be composed of pipe,

fittings, cements, and primers listed to ULC S636. M&G DuraVent

PolyPro polypropylene venting systems are ULC S636 listed.

NOTE

: When using polypropylene venting systems, all venting

materials used, including the vent terminations must be from the
same manufacturer.

Venting Systems

CARBON MONOXIDE POISONING HAZARD

Failure to follow the instructions outlined below for each

appliance being placed into operation could result in carbon

monoxide poisoning or death.
For all venting configurations for this appliance and other gas

appliances placed into operation for this structure, provisions

for adequate combustion, ventilation, and dilution air must be

provided in accordance with:

U.S.A. Installations

: Section 9.3 of the current edition of

NFPA 54/ANSI Z223.1, Air for Combustion and Ventilation

and applicable provisions of the local building codes.

Canadian Installations

: Part 8 of current edition of

CAN/CSA

−

B149.1. Venting Systems and Air Supply for

Appliances and all authorities having jurisdiction.

WARNING

RECOMMENDED SUPPORT FOR

VENT TERMINATION

It is recommended that sidewall vent terminations of over 24

inches (0.6 M) in length or rooftop vent terminations of over

36 inches (1 M) in length be supported by EITHER the

factory accessory vent termination kit or field

−

supplied

brackets or supports attached to the structure. A factory

accessory vent termination kit may be used for direct vent

terminations. Termination kits are available for 2

−

in. or 3

−

in.

pipe. See Table 13 for available options.

NOTICE

912S

Summary of Contents for 912S






















































































Search results

Summary of Contents for 912S

Reviews:

Related manuals for 912S

Brands by name

Popular brands

Bryant 912S, Installation, Operating And Service Instructions

Search results

Summary of Contents for 912S

Reviews:

Related manuals for 912S

Brands by name

Popular brands