Bryant 912S Installation, Operating And Service Instructions Download

Page: 4 / 85

9. The furnace may be used for construction heat provided that

the furnace installation and operation complies with the first

CAUTION

in the

LOCATION

section of these instruc-

tions.

10. These Multipoise Gas

−

Fired Furnaces are CSA design

−

cer-

tified for use with natural and propane gases (see furnace

rating plate) and for installation in alcoves, attics, base-

ments, closets, utility rooms, crawlspaces, and garages. The

furnace is factory

−

shipped for use with natural gas. A CSA

(A.G.A. and C.G.A.) listed accessory gas conversion kit is

required to convert furnace for use with propane gas.

11. See Table 2 for required clearances to combustible construc-

tion.

12. Maintain a 1

−

in. (25 mm) clearance from combustible ma-

terials to supply air ductwork for a distance of 36 in. (914

mm) horizontally from the furnace. See NFPA 90B or local

code for further requirements.

13. These furnaces SHALL NOT be installed directly on carpet-

ing, combustible tile, or any other combustible material oth-

er than wood flooring. In downflow installations, factory

accessory floor base MUST be used when installed on com-

bustible materials and wood flooring. Special base is not re-

quired when this furnace is installed on manufacturer’s Coil

Assembly Part No. CNRV, CNPV, CAP, or CAR or when

Coil Box Part No. KCAKC is used. See Table 2 for clear-

ance to combustible construction information.

Important Installation and Start

−

up Procedures

Failure to follow this procedure may result in a nuisance

smoke or odor complaint.
The manifold pressure, gas rate by meter clocking,

temperature rise and operation must be checked after

installation. Minor smoke and odor may be present

temporarily after start

−

up from the manufacturing process.

Some occupants are more sensitive to this minor smoke and

odor. It is recommended that doors and windows be open

during the first heat cycle.

NOTICE

INTRODUCTION

This 4

−

way multipoise Category IV condensing furnace is CSA

design

−

certified as a direct

−

vent (2-pipe) or non-direct vent

(1-pipe) furnace. See Fig. 2. The furnace is factory

−

shipped for

use with natural gas. The furnace can be converted in the field for

use with propane gas when a factory-supplied conversion kit is

used. Refer to the furnace rating plate for conversion kit

information.
These furnaces are not approved for installation in recreational

vehicles or outdoors. Single

−

stage furnaces (40,000 through

120,000) are approved for installation in manufactured

housing/mobile homes with manufacturer

−

approved accessory.

The conversion kit is required for use with both natural and

propane gas. The furnace must also be installed on a

factory-supplied accessory combustible floor base or evaporator

coil casing.
This furnace is designed for minimum continuous return

−

air

temperature of 60

F (15

C) db or intermittent operation down to

F (13

C) db such as when used with a night setback

thermostat. Return-air temperature must not exceed 80

F (27

db. Failure to follow these return-air temperature limits may affect

reliability of heat exchangers, motors, and controls. See Fig.

The furnace should be sized to provide 100 percent of the design

heating load requirement plus any margin that occurs because of

furnace model size capacity increments. None of the furnace

model sizes can be used if the heating load is 20,000 BTU or

lower. Use Air Conditioning Contractors of America (Manual J

and S); American Society of Heating, Refrigerating, and

Air-Conditioning Engineers; or other approved engineering

method to calculate heating load estimates and select the furnace.

Excessive oversizing of the furnace may cause the furnace and/or

vent to fail prematurely, customer discomfort and/or vent freezing.
Failure to follow these guidelines is considered faulty installation

and/or misapplication of the furnace; and resulting failure, damage,

or repairs may impact warranty coverage.
For accessory installation details, refer to the applicable instruction

literature.

NOTE

: Remove all shipping materials, loose parts bag, and

literature before operating the furnace. See Table 1.

CODES AND STANDARDS

Follow all national and local codes and standards in addition

to these instructions.

The installation must comply with

regulations of the serving gas supplier, local building, heating,

plumbing, and other codes. In absence of local codes, the

installation must comply with the national codes listed below and

all authorities having jurisdiction.
In the United States and Canada, follow all codes and standards for

the following:

Safety

US: Current edition of National Fuel Gas Code (NFGC) NFPA

54/ANSI Z223.1 and the Installation Standards, Warm Air

Heating and Air Conditioning Systems ANSI/NFPA 90B

A manufactured (Mobile) home installation must conform with

the Manufactured Home Construction and Safety Standard, Title

24 CFR, Part 3280, or when this standard is not applicable, the

Standard for Manufactured Home Installation (Manufactured

Home Sites, Communities, and Set-Ups),ANSI/NCS A225.1,

and/or CAN/CSA-Z240, MH Series Mobile Homes

CANADA: Current edition of National Standard of Canada,

Natural Gas and Propane Installation Code (NSCNGPIC)

CAN/CSA B149.1

General Installation

US: NFGC and the NFPA 90B. For copies, contact the National

Fire Protection Association Inc., Batterymarch Park, Quincy,

MA 02269; or for only the NFGC contact the American Gas

Association, 400 N. Capitol, N.W., Washington DC 20001

CANADA: NSCNGPIC. For a copy, contact Standard Sales,

CSA International, 178 Rexdale Boulevard, Etobicoke

(Toronto), Ontario, M9W 1R3, Canada

Combustion and Ventilation Air

US: Section9.3 of the current edition of NFPA54/ANSI Z223.1

Air for Combustion and Ventilation

CANADA:Part 8 of the current edition of CAN/CSA B149.1,

Venting Systems and Air Supply for Appliances

Duct Systems

US and CANADA: Air Conditioning Contractors Association

(ACCA) Manual D, Sheet Metal and Air Conditioning Contractors

National Association (SMACNA), or American Society of Heating,

Refrigeration, and Air Conditioning Engineers (ASHRAE) 2005

Fundamentals Handbook Chapter 35

Acoustical Lining and Fibrous Glass Duct

US and CANADA: Current edition of SMACNA, NFPA 90B as

tested by UL Standard 181 for Class I Rigid Air Ducts

Gas Piping and Gas Pipe Pressure Testing

US: Current edition of NFPA 54/ANSI Z223.1 NFGC; Chapters

5, 6, 7, and 8 and national plumbing codes.

CANADA: Current edition of CAN/CSA

−

B149.1, Parts 4, 5, 6,

and 9.

In the state of Massachusetts:

This product must be installed by a licensed plumber or gas fitter.

When flexible connectors are used, the maximum length shall

not exceed 36 in. (914 mm).

When lever type gas shutoffs are used they shall be T

−

handle type.

The use of copper tubing for gas piping is not approved by the

state of Massachusetts.

912S

Summary of Contents for 912S






















































































Search results

Summary of Contents for 912S

Reviews:

Related manuals for 912S

Brands by name

Popular brands

Bryant 912S, Installation, Operating And Service Instructions

Search results

Summary of Contents for 912S

Reviews:

Related manuals for 912S

Brands by name

Popular brands