Bryant HUM Installation And Start-Up Instructions Manual Download | Manualshive

Page: 12 / 12

background image

V.

OPERATION

When relative humidity falls to humidistat set point, the humidistat
switch makes contact and starts humidifier. In some central unit
humidifier systems, furnace fan must be operating before humidi-
fier will start. An increase in relative humidity above set point will
stop humidifier.

VI.

CHECKOUT

Place system in operation and observe at least 1 complete cycle to
make certain that all components are functioning properly.

Fig. 21—Humidistat Installation Schematic

A97105

CASE

MOUNTING TEMPLATE

MOUNTING SCREWS (2)

FOAM GASKET

MAKE OPENING IN DUCT

MOUNT HUMIDISTAT CASE

ALTERNATE PROCEDURE:

DRILL SIX 1/4 IN.
DIAMETER HOLES

RECOMMENDED HUMIDISTAT SETTING

OUTSIDE

TEMPERATURES

RECOMMENDED

HUMIDISTAT SETTING

-20°F

15%

-10°F

20% (LO)

0°F

25%

+10°F

30%

+20°F

35%

+30°F

40% (MED)

© 1998 Bryant Heating & Cooling Systems 7310 W. Morris St. Indianapolis, IN 46231

—12—

Printed in U.S.A.

iihum561

Catalog No. 13HU-MB1

«
...
10
11
12

Summary of Contents for HUM













Reviews:

No comments

Related manuals for HUM

Airtek SMART CYCLE PLUS 100

Brand: Parker Pages: 45

Brand: Master Pages: 75

Brand: Champion Pages: 12

Brand: Champion Pages: 20

Brand: Amcor Pages: 4

Brand: Aprilaire Pages: 14

Brand: Aprilaire Pages: 16

Brand: Viking Equipment Pages: 2

Brand: Ideal Air Pages: 8

Brand: Stadler Form Pages: 52

Brand: Elsteam Pages: 41

Brand: Skuttle Indoor Air Quality Products Pages: 1

Brand: G21 Pages: 84

Brand: UFESA Pages: 26

Brand: UFESA Pages: 102

Brand: Haier Pages: 32

Brand: Lanaform Pages: 88

Brand: Paris Rhone Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands