background image

 Eshop:

www.emareg.cz

Email:

shop@emareg.cz

w

w

w

.e

M

A

R

eg

.c

z

BRYMEN warrants to the original product purchaser that each product  it  manufactures
will be free from defects in material and workmanship under normal use and service
within a period of one year from the date of purchase. BRYMEN's warranty does not
apply to accessories, fuses, fusible resistors, spark gaps,

varistors, batteries or any

product  which,  in  BRYMEN's  opinion,  has  been  misused,  altered,  neglected,  or
damaged by accident or abnormal conditions of operation or handling.

To obtain warranty service, contact your nearest BRYMEN authorized agent or send
the  product, with proof of purchase and description of the difficulty, postage and
insurance prepaid, to BRYMEN TECHNOLOGY CORPORATION. BRYMEN assumes
no  risk  for  damage  in  transit.    BRYMEN  will,  at  its  option,  repair  or  replace  the
defective product free of charge.  However, if BRYMEN determines that the failure was
caused  by  misused,  altered,  neglected,  or  damaged  by  accident  or  abnormal
conditions of operation or handling, you will be billed for the repair.

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHE R WARRANTIES,
EXPRESSED  OR  IMPLIED,  INCLUDING  BUT  NOT  LIMITED  TO  ANY  IMPLIED
WARRANTY  OR  MERCHANTABILITY  OR  FITNESS  FOR  A  PARTICULAR
PURPOSE  OR  USE.    BRYMEN  WILL  NOT  BE  LIABLE  FOR  ANY  SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

BRYMEN TECHNOLOGY CORPORATION

TEL:+886 2 2226 3396

FAX:+886 2 2225 0025

http://www.brymen.com

PRINTED ON RECYCLABLE PAPER, PLEASE RECYCLE

COPYRIGHT © MMXVIII Btc,        ALL RIGHTS RESERVED

P/N: 7M1C­1571­0000

PRINTED IN TAIWAN

Summary of Contents for BM031

























Reviews: