background image

24/25           

 

 

 

 

 

 

 

 

9. SITING 

 

There are two basic requirements for a good site: high average wind speed and low wind 
turbulence. 
The lower the wind turbulence, the lower stress the wind turbine will have to endure. 
Lower turbulence also results in more power, the zone with high wind speed but high 
turbulence is not a desirable site. 

             

 

Power in the wind is the cubic function of the wind speed. This means 
that small changes in wind speed can have dramatic changes in output. 

Even slight changes have dramatic effects. 

 

CAUTION: 

DO NOT INSTALL THE TURBINE WHERE THE 

PATH OF THE BLADES CAN BE REACHED. 

 

CAUTION: 

DO NOT APPROACH THE TURBINE FOR ANY 

REASON UNLESS ROTOR BLADES ARE STOPPED. 

 

Please add safety notice, when the rotor is turning, the blades are nearly transparent. 

so made sure, that nobody can come in touch with the rotation blades, this is specially very 

important at boats and yachts. Also take care, that nothing can com in to the turning rotor, 
like some robe. 

When this wind is string, the rotor blades are a little deforming, in the direction of the pole. 

so it is important, that the pole have in the area of the rotor blades, no bigger diameter then 55 mm. 

also you can choice proper position of your BSG according to the figure 9: 

 

Summary of Contents for BLACK 300-12V


























Reviews:

Related manuals for BLACK 300-12V