8
Description:
1.
OPEN/CLOSE BUTTON
Press to load or eject disk. Each press will open or close the disk tray.
NOTE: disc holder will not open unless stop or pause button has been pushed first.
2.
MEMORY CUE / SAMPLER BANKS BUTTONS
Two functions :
Memory CUE :
To save a cue point, press the MEMORY button then select one of the four memories. The last cue point is saved on the memory you
select. To call a cue point, just press the memory button where you save the cue point ( The playback start automatically )
Sample backup :
The sample are just loop make from the cue point you saved ( 5s for each memory ). For example, if you have save a cue point in the
memory 1, you sample will be a loop of 5s from this cue point.
To read the sample, push the sampler button and select the bank you want. If you are in the single mode ( sample button flac, the
sample will be read one time. If you are in the continue mode, the sample will be read in loop until you push the sampler button.
3.
MEMORY BUTTON
This button is used to memories cue points ( 3 memories ). It’s used to save sample to ( see description after )
4.
SAMPLER BUTTON
Used to read the sample you saved. To read the sample, push the sampler button and select the bank you want. If the SAMPLER
button lights, the sample will be read one time. If the SAMPLER button flashes, the sample will be read in loop until you push the
sampler button.
Note :
-
Samples will be save even you eject the cd. To clean the samples, you must to save in it place or you must to switch your
cd player off.
-
The TIME FX button (1) is used to adjust the speed of the track ( If the HOLD button is on ) or like the pitch bend button ( if the
HOLD button is off ) & the RATIO FX button (2) is used to adjust the level of the sample. The wheel operate just in the scratch
mode ( and if the cd is eject ).Sampler button
5.
PLAY/PAUSE BUTTON
Each time you press the PLAY/PAUSE button, the operation changes from play to pause or from pause to play.
6.
CUE BUTTON
Pressing the CUE button during play provides a return to the position at which play was started
7.
SEAMLESS LOOP
There are A, BLOOP/EXIT, RELOOP buttons.
1)
Use IN button to set the start point (A point)
2)
OUT “end p oint” (B point). Press OUT to set end point (B point) and start loop playback automatically. LOOP lights on LCD.
3)
To exit the loop playback, Press OUT to exit the loop playback. And the playback goes on from B point.
4)
Return LOOP : Return to the loop playback by pressing RELOOP.
5)
Change “START POINT” & “END POINT” by pressing IN & OUT in play mode.
The interval between A and B point must be more than 20 frames, or the B point will be canceled, then Loop function disappear, and
LOOP fades on the LCD.
8.
SKIP TRACK BUTTON
These buttons are used to change track. If you push the left knob, you restart the track or you select the last track. If you push the
right knob, you select the next track.
9.
SEARCH WHEELS
Turn this wheel clockwise to scan in the forward direction. Turn this wheel counter clockwise to scan in the reverse direction The
scanning speeds up when the shuttle dial is turned faster
10. LCD DISPLAY
This display shows you time, pitch value ( or BPM value ), level of the anti-shock memory.
11. PITCH RANGE ADJUSTMENT BUTTON
When pitch function has been turned on, holding the button then tapping the PITCH BEND + button to change the pitch percentage
the PITCH SLIDER will react to . The PITCH BUTTON’s LED will indicate which pitch percentage mode you are in : +/-4%, +/-8%, +/-
16% or +/- 100%.
12. MASTER TEMPO ( TEMPO LOCK )
This button is used to choose the tempo lock mode and the pitch control mode. Tempo lock mode allows tempo change while
maintaining the original key.
13. PITCH ON/OFF BUTTON
Using this button you can validate the pitch slider’s functioning
14. PITCH SLIDER
Use this fader to increase or decrease the speed of the track
15. TIME BUTTON
The TIME button will switch the time value described in the time meter between elapsed play time, track remaining time, and total
remaining time.
16. SGL ( SINGLE )/CTN ( CONTINU )
This function allows you to choose between single track play or continuous track play (all tracks in order).
