www.BSTsound.com
6
13. CROSS-FADER
This horizontal slider provides clean seagues between all the
sources
14. BEAT LIGHTS
shows the Beats Per Minute of channel.
15. MONO/STEREO SELECTOR.
This switch is used to change your output signal ( MAS 1 or
MAS 2 ) in the mono mode.
16. CHANNEL MIXING PHONE SYSTEM ( CUE / MAS )
This potentiometer allows to make a mix in the headphone,
from the selected CUE channel and the master output (PGM).
17. OUTPUT LEVEL SELECTOR
Push switch for output level 1.5V/0.775V selection switch for
master 1 &2.
18. HEADPHONE INPUT
The headphone jack is where you plug your headphone.
19. SAM Q, EFX Q, SPLIT Q SELECTOR
SAM Q : cue ON/OFF switch for sampler
EFX Q : cue ON/OFF switch for EFX
SPLIT Q : Use the split Q button on spilt the signal from each
channel so that channel 1 will be heard in one
earphone and channel 2 will be heard in the other
earphone.
20. SAMPLER ON/OFF SELECTOR.
This button enables you to start or stop the play or record
mode of the sampler.
21. ECHO ON/OFF SELECTOR
This button permits the start or the stop of the echo of the
channel you select
22. PITCH CONTROL
The item comes equipped with a sampler pitch control. To get
a perfect sampler, set the control to its center position and
record the sample.
During the playback, rising or lowering the control will raise or
lower the pitch of the sample. The center position will remain
as normal pitch.
23. DELAY TIME CONTROL
The delay control changes the amount of time between the
original sound and the delayed sound.
24. PAN SAMPLER
Pan pot controls the input stereo signal to either the left or
right or both sampler.
25. REPEAT LEVEL CONTROL
The repeat control varies the number of echo created by the
original signal, the number of echo that you can create
depends on the strength of the original signal.
26. HEADPHONE LEVEL CONTROL
Use to adjusting the level of the stereo headphone.
27. SAMPLER LEVEL CONTROL
Used to adjust the level of the sampler
28. ECHO LEVEL CONTROL
Use to adjust the level of the echo
29. MEMORY FUNCTION SELECTION BUTTON
When 1 bank can be used 8,8,8 or 24 secondes.
When 3 bank can be used 8 secondes each.
30. LED INDICATOR
For 8,8,8 or 24 sec. Each.
31. SOUND EFFECT
8 differents kinds of sound effect for choice :
Clap Laugh
Oooh ghost
Kiss tempo
Bomb Baby
32. SAMPLER FUNCTION SELECTION PUSH BUTTON
(1) WRITE : to record sound into sampler
(2) SINGLE : to play one time sampler memory
(3) REPEAT : To play continually sampler memory
33. PLAYBACK SWITCH
When the playback button is in the off position ( the playback
indicator will be OFF ) and the mode selector switch in either
the SINGLE or REPEAT mode, pressing the start/stop button
will cause the sampler to play along with the selected source.
When the playback button is in the ON position ( the playback
indicator illuminates red ) starting the sampler mutes the
selected source. When the sampler ends, the source
automatically turns back on
34. EFX IN LEVEL CONTROL
The level of the signal being EFX IN ( Receive ) can be
adjusted with this button.
35. EFX OUT LEVEL CONTROL
The level of the signal being EFX OUT ( send ) can be
adjusted with this button.
36. POWER SWITCH
Press this switch to turn the power on, press again to turn the
power off. When operating this switch, make sure that all
controls are set at minimum position.
37. LIGHT ADP
38. DISPLAY MODE
Displays source selector switch ( MASTER 1, MASTER 2,
CUE )
39. EFFECTS LEVEL CONTROL
Used to adjust the level of the effect
40. ROTARY BALANCE MASTER 2
Use for adjusting the level of the right/left channel of the
master 2
41. VU-METER
42. ROTARY BALANCE MASTER 1
Use for adjusting the level of the right/left channel of the
master 1
43. INPUT SELECTOR ( 2 POSITIONS ) CD/LINE
This selector is used to choose the input signal between CD
or LINE
44. BUTTON START/STOP
You can control start or stop of your cd player. When
operating this button, the led switches on and the play mode
starts on your cd player. When pressing this button a second
time, the led switches off and your cd player pauses.
45. INPUT SELECTOR ( 3 POSITIONS ) PHONO/LINE
This selector is used to choose the input signal between CD,
PHONO or LINE
46. LED PEAK
Each channel has its own led peak. This led indicates your
input signal is to high and the sound is distorted.
CONNECTION :
47. AC CORD
Plug the AC cord in this socket.
48. POWER SUPPLY SELECTOR
Countries are not the same power supply voltage. This
selector is used to choose the good voltage.
49. BATTERY BACK UP FOR SAMPLER
This battery is used to save the sound recorded in the
sampler memory.
50. PHONE JACK FOR SAMPLER REMOTE
Plug a momentary normally open foot switch a 6.35mm jack
into the remote START/STOP jack on the rear pannel.
This socket allows you to trigger the sampling process with
the foot switch leaving your hand free to do other things.
51. REC OUTPUT
The REC jacks can be used to connect the mixer to the
record input of your recorder enabling to record your mix.
52. MASTER 2 OUTPUT
The master jacks allows you to hook up additional amplifier.
53. MASTER 1 OUTPUT
The master jacks are used to connect your main amplifier.
54. OUT EFX CONNECTOR
Connect this output jacks to the input of an effect or an echo
chamber.
