INSTRUCTIONS FOR USE DVR ELECTRONIC SAFE AND CSMO SAFE
Cód. 140195 Rev. 02/15
www.btv.es
Atención al cliente: 902 877 873
1.TECHNICAL FEATURES
* Power supply: 6 Volts (4 batteries, type AA, R6 or equivalent). Look at the sell-by date on the batteries. Alkaline batteries
recommended. Watch out carefully for the
expiration date
of the batteries before installing them in your safe. Do not use
rechargeable batteries. Check and replace the batteries every year.
* One user code (4 digits) plus one emergency code (8 digits).
* Automatic blocking system for 5 minutes when more than 10 consecutive incorrect codes are entered.
* Low batteries’ warning system.
* Inside easy access to replacement of batteries.
* External power supply, to open your safe in case the batteries are completely discharged
.
Read carefully these instructions and warranty before any action.
IMPORTANT!
Check every
action with
open door
,
before
closing it.
2. FIRST USE
2.1.
Fit four batteries as indicated on point 6 of this instruction manual.
2.2.
Then open and close the safe several times (point 3).
2.3.
Change the original user code for your own one (point 4)
3. OPENING/CLOSING INSTRUCTIONS
3.1. Introduce your
code number
. All the safes have the code
1 2 3 4 5 6
programmed when used for the first time. After
you press each digit, there will be a short beep and the red light will turn on. If you do not press any key for 7
consecutive seconds, the unit will disconnect; in this case, start again from the beginning.
3.2. If the code entered was correct, the green light will turn on and the bolts will move to the open position while this light
stays on. When the green light turns you could open the door.
3.3. To close the safe, close the door and enter the code. The red light will turn on while the bolts move. In case the bolts
find some obstacle when closing, you will hear five beeps, the red light will turn on, the bolts will retrieve to the open
position and the safe will keep open. Locate and remove the obstacle, close the door and enter the code to close the
safe.
Opening/closing example:
1 2 3 4 5 6
4. PROGRAMMING OR CHANGING YOUR CODE
A. User code
: every safe has been programmed with the same user code.
For your security
do not forget to change it
.
A.1. Open the safe following the instructions for opening (point 3).
A.2. Press the key
“#/Reset
”; the red light will turn on and a programming tone will be heard.
A.3. Introduce your current code (from factory, the number 1 2 3 4 5 6). If the code is correct, you will hear the
programming tone.
A.4. Enter the
new code
(from 2 to 15 digits), followed by the key “
C
”. After this, you will hear again the programming tone.
A.5. Finally, introduce again the
new code
, so as to confirm it. A programming tone will be heard, the green light will turn
on, indicating that the new code has been programmed, and the bolts will move to the closed position. If the
programmation was not corretly done, you will hear the error tone and you should start from step A.2.
A.6. Before closing the door, check the new code at least
three times
, following the opening instructions.
Example of programming:
A.1.
1 2 3 4 5 6
current code to open the safe
A.2.
#/Reset
press the key “#/Reset”
A.3.
1 2 3 4
introduce current code
A.4.
9 7 6 5 C
introduce new code + key “C”
A.5.
9 7 6 5
repeat the new code
B. Emergency code
: Every safe has been programmed with an
exclusive emergency code
. We recommeded you
not to
change it
. If you wish to change it, please follow carefully the next sequence:
B.1. Open the door with your emergency code (see point 5)
B.2. Press the key
“#/Reset
”; the red light will turn on and a programming tone will be heard.
B.3. Introduce your current code (from the factory, the one in the enclosed envelope). If the code is correct, you will hear
the programming tone.
B.4. Press the key “
2
”.
B.5. Press the key
“#/Reset
”; the red light will turn on and 2 short beeps will be heard.
B.6. Enter the
new code
(from 2 to 15 digits) followed by the key “C”. After this, you will hear again the programming tone.
