INSTRUCTIONS FOR USE DVR ELECTRONIC SAFE AND CSMO SAFE
Cód. 140195 Rev. 02/15
www.btv.es
Atención al cliente: 902 877 873
B.7. Finally, introduce again the
new code
, so as to confirm it. A programming tone will be heard, the green light will turn
on, indicating that the new code has been programmed and the bolts will move to the closed position. If the
programmation was not correctly done, you will hear an error tone and you should start form step B.2.
B.7. Before closing the door, check the new code at least
three times
, following the opening instructions.
Example of programming the emergency code:
B.1.
8 7 6 5 4 3 2 1
(open with the emergency code)
B.2.
#/Reset
(press the key “#/Reset)
B.3.
8 7 6 5 4 3 2 1
(introduce current emergency code)
B.3.
2
(press the key “2”)
B.4.
#/Reset
(press the key “#/Reset)
B.5.
7 6 1 0 8 4 2 2 C
(introduce new emergency code + key C)
B.6.
7 6 1 0 8 4 2 2
(repeat new emergency code)
BEWARE!: If you omit steps B.3. and B.4., you will always modify the user code 1.
NOTE:
We strongly suggest that you program code numbers which are easy for you to remember, such as friends’
telephone numbers, birth dates, car licence plates, etc.. Do not trust memory, and do
write and keep your code number in
two different secret places for not mislaying it
.
5. EMERGENCY OPENING
Your safe is provided with an
envelope
which contains:
5.1.
One emergency code number
to open your safe in case that you have forgotten your normal opening code number.
Enter your emergency code number as usual. The green light will turn on, showing that you can now open your safe.
For your security
the emergency code should be changed
, so do as explained in point 6.B.
5.2.
External power supply
, to open your safe in case the batteries are completely discharged. To use it, put an
alkaline
9V
battery (6F-22 S type) against the two black dots in the keypad, watching out that the polarity is correct. Then, while
holding the 9V battery on the keypad, introduce your code number, and open your safe as usual. As soon as you have
opened your safe, do not forget to replace all four batteries for new alkaline ones. Alkaline batteries are recommended
for long-life and armour.
6. OPENING DELAY PROGRAMMATION
This function activates a delay which blocks the opening of the safe for 1 to 99 minutes after the user code has been
entered. The red light flashes during the delay time, and when it is over, a short beep will be heard, the system unblocks
and allows the opening of the safe for 5 seconds. To activate or desactivate this function, the
door must be in the open
position
.
a) To
activate
this function:
1. Enter the following secuence: “C 1 0 0”. The red light will turn on and you will hear the programming tone.
2. Introduce the desired
delay number of minutes
, from
01 to 99
. You will hear the programming tone.
b) To
desactivate
this function: just program the delay with
0 minutes
time.
7. OTHER FEATURES
*
Incorrect code number
: if the code number that you have entered is not the one programmed before, you will hear a
special tone indicating that this code number is not correct. In this case, go back to step 1 of the opening instructions.
*
Obstacle
: In case the bolts find some obstacle when closing, you will hear five beeps, the red light will turn on, the bolts
will retrieve to the open position and the safe will keep open. Locate and remove the obstacle, close the door and enter
the code to close the safe.
*
Blocking system
: provides aditional security: if incorrect code numbers are entered more than 10 times consecutively,
some long beeps will be heard, and the safe will stay locked for 5 minutes. During this time, the red light will be
flashing, and it will be impossible to open the safe. When the 5 minutes have gone by, you wil be able to open the safe
as usual.
*
Low batteries
: the system detects whether the batteries are very low. If this is the case, you will hear some tones
followed by the flashing red light when you press some key: you will still be able to operate your safe around 100 times,
but it is highly recommended that you change all four batteries at that time.
*
Replacement of batteries
: the batteries’ holder can be found in a compartment inside the door, under a small cover.
Once you have removed the cover, change all FOUR batteries for new ones and secure the cover back. Check the right
functioning of the safe before locking it.
