Faire afficher le niveau de charge du store
Le store doit être à la position limite supérieure.
Le store doit être à la position
de la limite supérieure
Maintenez enfoncé le
bouton
HAUT
enfoncé pendant
environ 5 secondes
Le store se déplace à la
position représentant le niveau
de charge restant
Activer ou désactiver le voyant de recharge
Le store doit être à la position limite inférieure.
Maintenez enfoncé le bouton
BAS
pour le désactiver
Réponse du moteur :
Le voyant rouge clignote 3X
Le voyant rouge clignote 3X
Le moteur de votre store est doté d’une pile rechargeable de 5V.
Recharger le moteur à l’aide d’un chargeur :
Pour recharger la pile à l’aide du chargeur, branchez celle-ci sur une prise de courant et reliez-la
au connecteur du moteur. Laissez-la branchée pendant environ six heures.
Lorsque le voyant devient vert, continuez la recharge pendant une heure ou deux de plus pour s’assurer
que la recharge est complète.
Maintenez enfoncé le bouton
BAS
pour l’activer
Réponse du moteur :
Maintenez enfoncé le bouton
HAUT
Réponse du moteur :
18
Position limite supérieure
Position limite inférieure
Pourcentage utilisé
Pourcentage de
charge restant
.
Pair motor with controller
Check motor direction
Consult user manual for your
controller for information on
selecting channel.
Damage to shade may occur when operating motor prior to
setting limits. Attention should be given.
Reversing motor direction using this method is only possible
during initial set-up
Hold
P1
button on
motor head.
To check travel direction of shade, press
UP
or
DOWN
on controller.
Quick Press
= Step
Long Press
= Continuous Travel
To reverse shade direction, hold both
UP
and
DOWN
.
Until the motor responds.
Select channel on
controller.
Hold
STOP
on
controller.
Approx.
Approx.
Motor Response
Motor Response
Motor Response
Motor is now in step mode and ready for setting limits
IMPORTANT
IMPORTANT
IMPORTANT
5
INITIAL SET UP
OR
.
Pair mot
or with contr
oller
Check motor dir
ection
Consult user manual for y
our
contr
oller f
or information on
selecting channel.
Damage to shade ma
y occur when oper
ating motor prior t
o
setting limits. Att
ention should be giv
en.
Rev
ersing mot
or direction using this method is onl
y possibl
e
during initial set-up
Hold
P1
button on
motor head.
To check tr
avel dir
ection of shade, pres
s
UP
or
DOWN
on contr
oller
.
Quick Pres
s
= Step
Long Pres
s
= Continuous Trav
el
To r
ever
se shade direction, hol
d both
UP
and
DOWN
.
Until the motor r
esponds.
Select channel on
contr
oller
.
Hold
STOP
on
contr
oller
.
Approx.
Approx.
Motor R
esponse
Motor R
esponse
Motor R
esponse
Motor is no
w in step mode and r
eady for setting limit
s
IMPORTANT
IMPORTANT
IMPORTANT
5
INITIAL SET
UP
OR
.
Pair mot
or with contr
oller
Check motor dir
ection
Consult user manual for y
our
contr
oller f
or information on
selecting channel.
Damage to shade ma
y occur when oper
ating motor prior t
o
setting limits. Att
ention should be giv
en.
Rev
ersing mot
or direction using this method is onl
y possibl
e
during initial set-up
Hold
P1
button on
motor head.
To check tr
avel dir
ection of shade, pres
s
UP
or
DOWN
on contr
oller
.
Quick Pres
s
= Step
Long Pres
s
= Continuous Trav
el
To r
ever
se shade direction, hol
d both
UP
and
DOWN
.
Until the motor r
esponds.
Select channel on
contr
oller
.
Hold
STOP
on
contr
oller
.
Approx.
Approx.
Motor R
esponse
Motor R
esponse
Motor R
esponse
Motor is no
w in step mode and r
eady for setting limit
s
IMPORTANT
IMPORTANT
IMPORTANT
5
INITIAL SET
UP
OR
Set Limits
To save upper limit, hold
UP
and
STOP
.
Cycle shade up and down prior to setting limits to settle fabric
Move shade to the desired highest or lowest position by
pressing the
UP
or
DOWN
buttons on controller.
Motor Response
OR
Approx.
Move shade to the desired highest or lowest position
by pressing the
UP
or
DOWN
buttons
on controller.
OR
After setting limits, motor will automatically exit from initial set-up mode.
To save lower limit, hold
DOWN
and
STOP
.
Motor Response
Approx
.
IMPORTANT
IMPORTANT
SEC
Environ
Set Limits
To save upper limit, hold
UP
and
STOP
.
Cycle shade up and down prior to setting limits to settle fabric
Move shade to the desired highest or lowest position by
pressing the
UP
or
DOWN
buttons on controller.
Motor Response
OR
Approx.
Move shade to the desired highest or lowest position
by pressing the
UP
or
DOWN
buttons
on controller.
OR
After setting limits, motor will automatically exit from initial set-up mode.
To save lower limit, hold
DOWN
and
STOP
.
Motor Response
Approx
.
IMPORTANT
IMPORTANT
SEC
Environ
Set Limits
To save upper limit, hold
UP
and
STOP
.
Cycle shade up and down prior to setting limits to settle fabric
Move shade to the desired highest or lowest position by
pressing the
UP
or
DOWN
buttons on controller.
Motor Response
OR
Approx.
Move shade to the desired highest or lowest position
by pressing the
UP
or
DOWN
buttons
on controller.
OR
After setting limits, motor will automatically exit from initial set-up mode.
To save lower limit, hold
DOWN
and
STOP
.
Motor Response
Approx
.
IMPORTANT
IMPORTANT
SEC
Environ
Using P2 Button on existing controller to add a new controller or channel
Using a pre-existing controller to add or delete a controller or channel
A
= Existing controller or channel (to keep)
B
= Controller or channel to add or remove
A
= Existing controller or channel (to keep)
B
= Controller or channel to add or remove
Press
P2
on
controller
A
.
Press
P2
on
controller
A
.
Press
P2
on
controller
A
.
Press
P2
on
controller
A
.
Press
P2
on the
controller
B
to remove
it.
Press
STOP
on an new
controller to add it.
Motor Response
Motor Response
Motor Response
Motor Response
Motor Response
Motor Response
7
CONTROLLERS AND CHANNELS
Consult user manual for your controller or sensor
Consult user manual for your controller or sensor
IMPORTANT
IMPORTANT
Vérification des piles
Charger la pile du moteur
