manualshive.com logo in svg

Buell 2007 ULYSSES, Service Manual

The Buell 2007 ULYSSES Service Manual is a comprehensive guide for motorcycle enthusiasts, providing detailed instructions for maintenance, repairs, and service procedures. This indispensable manual, available for free download at 88.208.23.73:8080, ensures you have the necessary resources to keep your ULYSSES in top-notch condition.

Share
Download
background image

 

2007 Buell Uylsses: Maintenance

1-37

 

HOME

 

STEERING HEAD BEARINGS

1.12

 

GENERAL

 

The steering head bearings are sealed, angular contact bear-
ings and do not require additional lubrication.

Check steering head bearing resistance:

 

●

 

At every 5000 mile (8000 km) service interval.

 

●

 

When storing or removing the motorcycle for the season.

 

INSPECTION

 

NOTES

 

●

 

Check that throttle cables do not bind when measuring
bearing resistance.

 

●

 

Steering head bearings are sealed and do not require
additional lubrication.

 

●

 

Steering head bearing resistance is not adjustable.
Replace bearings that do not meet resistance specifica-
tions.

 

1.

Detach clutch cable at handlebar.

2.

Place a scissor jack under jacking point and raise front
wheel off ground. For location of jacking point see 

2.32

EXHAUST SYSTEM

.

1

WARNING

1

WARNING

 

Steering must be smooth and free with no binding or
interference. Do not operate motorcycle with loose, worn
or damaged steering or suspension systems. Contact a
Buell dealer for repairs. Loose, worn or damaged steer-
ing or suspension components can adversely affect sta-
bility and handling, which could result in death or
serious injury. (00113a)

 

3.

Check steering stem bearings for notches by turning
front wheel full right and then left. Repeat if necessary.

4.

Next place wheel facing straight ahead and grabbing
both fork sides at the bottom move front-end forward and
back to check for steering head play.

5.

To inspect for correct steering head resistance turn front
wheel all the way to the right.

6.

See 

Figure 1-39. 

Hook a spring scale into the hole in the

front axle. With scale 90 degrees from fork leg, pull front
wheel to center position.

a.  The desired resistance to pull front wheel to center

is between 1-7 lbs (0.5-3.2 kg).

b.  If steering head resistance measurement is not

within specification, see 

 DETERMINING PROPER

RESISTANCE

.

7.

When adjustment is complete, attach clutch cable and
adjust. See 

1.8 CLUTCH.

 

DETERMINING PROPER 

 

RESISTANCE

 

1.

Detach clutch cable at handlebar and ensure that throttle
cables do not bind before measuring steering head bear-
ing resistance.

2.

Remove steering stem pinch fastener at upper triple
clamp.

3.

Loosen steering stem capnut and back off several turns.

4.

Remove lower triple clamp pinch fasteners, two per side.

5.

Tighten steering stem capnut to 38-42 ft-lbs (52-57 Nm).

6.

Turn front wheel all the way to the right.

7.

See 

Figure 1-39. 

Hook a spring scale into the hole in the

front axle. With scale 90 degrees from fork leg, pull front
wheel to center position.

8.

The desired resistance is between 1-7 lbs (0.5-3.2 kg).

 

NOTE

If the correct specification cannot be achieved, the steering
head bearings must be replaced. See 

2.18 STEERING

HEAD BEARINGS

.

 

9.

Once correct steering head resistance has been verified,
apply LOCTITE 271 to steering stem pinch bolt, install
and tighten to 20-22 ft-lbs (27-30 Nm).

10. Apply LOCTITE 271 to lower triple clamp fasteners,

install and tighten to 20-22 ft-lbs (27-30 Nm).

11. When adjustment is complete, attach clutch cable and

adjust. See 

1.8 CLUTCH.

 

12. Remove scissor jack.

 

Figure 1-39. Measuring Steering Head Bearing 

Resistance (Typical)

8421

Summary of Contents for 2007 ULYSSES








































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 ULYSSES

TVS Apache RTR 160 HYPER EDGE 2015 Owner'S Manual preview
Apache RTR 160 HYPER EDGE 2015
Brand: TVS Pages: 60
Cobra 602-3000 Instruction Manual preview
602-3000
Brand: Cobra Pages: 2
Kask PLASMA AQ Use And Care Booklet preview
PLASMA AQ
Brand: Kask Pages: 68
hepco & becker TRIUMPH Bonneville T 120 Quick Start Manual preview
TRIUMPH Bonneville T 120
Brand: hepco & becker Pages: 4
Wedze IM 16 S Manual preview
IM 16 S
Brand: Wedze Pages: 63
R&G CR0076BK Fitting Instructions Manual preview
CR0076BK
Brand: R&G Pages: 9
Suzuki Intruder VS700 Service Manual preview
Intruder VS700
Brand: Suzuki Pages: 526
KTM 690 Enduro R 2019 Owner'S Manual preview
690 Enduro R 2019
Brand: KTM Pages: 274
Zontes ZT310-X Service Manual preview
ZT310-X
Brand: Zontes Pages: 119
Honda CB650FA 2016 Owner'S Manual preview
CB650FA 2016
Brand: Honda Pages: 127
LAS 10323 Operating Instructions Manual preview
10323
Brand: LAS Pages: 22
Shad SH39 Owner'S Manual preview
SH39
Brand: Shad Pages: 2
Shad KIT TOPMASTER S0BN11ST Quick Start Manual preview
KIT TOPMASTER S0BN11ST
Brand: Shad Pages: 2
Shad KIT TOPMASTER S0SV69ST Quick Start Manual preview
KIT TOPMASTER S0SV69ST
Brand: Shad Pages: 2
Shad KIT TOPMASTER S0GL69ST Quick Start Manual preview
KIT TOPMASTER S0GL69ST
Brand: Shad Pages: 2
DAINESE AGV ARK User Manual preview
AGV ARK
Brand: DAINESE Pages: 59
Razor A5 CARBON LUX Owner'S Manual preview
A5 CARBON LUX
Brand: Razor Pages: 6
Petzl Elios 1 White Quick Start Manual preview
Elios 1 White
Brand: Petzl Pages: 5

Brands by name

Popular brands

Load more brands